Page Comparison

...

AFT Card Model	Firmware version	Change Log	Release Date
T116	v01, v01-base	More Info	(2012-12-31)
A116	v44	More Info	(2012-05-14)
A108	v44	More info	(2010-08-24)
A104	v45	More info	(2014-05-09)
A102	v40	More info	(2014-05-09)
A101	v40	More info	(2014-05-09)
A200	v13	More info	(2009-12-10)
A400	v11	More info	(2008-07-10)
A104(pmc framer)	v26	More info	(2007-07-10)
A301	v11	More info	(2007-07-10)
A14X	v08	More info	(2008-10-28)
A500	v35	More info	(2009-04-30)
A056	v01
B600 (cannot be updated)	v03	More Info	(2009-05-08)
B601	v04	More info	(2009-05-08)
B500	v44	More Info	(2012-09-07)
B700	v35	More Info	(2009-07-03)
U100	v21	More Info	(2009-09-11)

Archived firmware files: ftp.sangoma.com/firmware

...

Stop Asterisk
- amportal stop (For FreePBX 12 and below)
- fwconsole stop (For FreePBX 13 and above)
Stop the Sangoma Telephony driver (which is called 'Wanpipe')
- wanrouter stop

Being the firmware update process

Navigate to the following directly by typing:
-> cd /etc/wanpipe/util/wan_aftup/

Type the following command to run the upgrade
-> ./update_aft_firm.sh

You will notice an output similar to the example below (dependent on the telephony cards installed)

Code Block

[root@support-sys1 wan_aftup]# ./update_aft_firm.sh
modprobe wan_aften  > /dev/null
AFT card enabled
 
 
Sangoma AFT Series card update flash software (version 1.9)
 
 
Sangoma AFT card list:
 w1g1: AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=23 : CPU=A : PORT=1 : HWEC=256 : V=42 (Ver.42)
 
 
Please select card interface [def=w1g1; q=exit] >

specify the interface name that corresponds to your card, based on the output.
i.e. w1g1 then press <enter>

A list of available firmware versions will be presented. Select the latest/current firmware version, as referenced from the table at the beginning of this page.
Example:

Code Block
Please select card interface [def=w1g1; q=exit] > w1g1 List of available versions: Version no. 44 (filename=A108dm_0100_V44.BIN) Please specify version number [def=44; q=exit] > 44

If the list does not display the latest/current firmware that is seen in the table, you will need to upload the latest/current firmware file into your system and redo these steps.
To do this:
a. Right click on the firmware file in the table, located under the 'Firmware version' column and copy the link . This will copy a link to the location of that firmware file.
b. In you Linux command line, in the current directory of /etc/wanpipe/firmware/wan_aftup, type:
-> 'wget' then left click to paste the firmware file location.
i.e. wget ftphttps://ftp.sangoma.com/firmware/A108dm_0100_V44.BIN
-> This will auto download the firmware, assuming your system has internet access
c. now follow the steps again

After pressing <enter> the upgrade process will begin
Example:

Code Block
Please specify version number [def=44; q=exit] > 44 ABOUT TO board_reset FINISH board_reset w4g1: Current Sangoma Flash: Revision=44 ID=0x205B Erasing sectors Passed Updating flash 1%

Now that the firmware on your card has been updated, start your production environment back up.
1. Type the following, in your Linux command line, to start the telephony driver:
  -> wanrouter start
2. Start Asterisk by typing:
  -> amportal start (For FreePBX 12 and below)
  -> fwconsole start (For FreePBX 13 and above)

...

Stop Asterisk
- asterisk -rx "stop now" (or 'asterisk -rx "core stop now")
  If you are not using Asterisk, but another application that is using the Sangoma card, stop that application now with the relevant command(s)
Stop the Sangoma Telephony driver (which is called 'Wanpipe')
- wanrouter stop

Being the firmware update process

Navigate to the following directly by typing:
-> cd /etc/wanpipe/utils/wan_aftup

Type the following command to run the upgrade
-> ./update_aft_firm.sh

You will notice an output similar to the example below (dependent on the telephony cards installed)

Code Block

[root@support-sys1 wan_aftup]# ./update_aft_firm.sh
modprobe wan_aften  > /dev/null
AFT card enabled
 
 
Sangoma AFT Series card update flash software (version 1.9)
 
 
Sangoma AFT card list:
 w1g1: AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=23 : CPU=A : PORT=1 : HWEC=256 : V=42 (Ver.42)
 
 
Please select card interface [def=w1g1; q=exit] >

specify the interface name that corresponds to your card, based on the output.
i.e. w1g1 then press <enter>

A list of available firmware versions will be presented. Select the latest/current firmware version, as referenced from the table at the beginning of this page.
Example:

Code Block
Please select card interface [def=w1g1; q=exit] > w1g1 List of available versions: Version no. 44 (filename=A108dm_0100_V44.BIN) Please specify version number [def=44; q=exit] > 44

If the list does not display the latest/current firmware that is seen in the table, you will need to upload the latest/current firmware file into your system and redo these steps.
To do this:
a. Right click on the firmware file in the table, located under the 'Firmware version' column and copy the link . This will copy a link to the location of that firmware file.
b. In you Linux command line, in the current directory of /etc/wanpipe/utils/wan_aftup, type:
-> 'wget' then left click to paste the firmware file location.
i.e. wget ftphttps://ftp.sangoma.com/firmware/A108dm_0100_V44.BIN
-> This will auto download the firmware, assuming your system has internet access
c. now follow the steps again

After pressing <enter> the upgrade process will begin
Example:

Code Block
Please specify version number [def=44; q=exit] > 44 ABOUT TO board_reset FINISH board_reset w4g1: Current Sangoma Flash: Revision=44 ID=0x205B Erasing sectors Passed Updating flash 1%

Now that the firmware on your card has been updated, start your production environment back up.
1. Type the following, in your Linux command line, to start the telephony driver:
  -> wanrouter start
2. Start Asterisk by typing:
  -> asterisk

...

Versions Compared

Old Version 2

New Version 3

Key