Page Comparison

Parameter

Value 

Description

 CARD_TYPE

 AFT

Define AFT card type

AUTO_PCISLOT

YES
NO

Enable/Disable AUTO PCI detection. This parameter can be set to YES only if you have only one card of the same type.  If this option is enabled, PCISLOT/PCIBUS options are ignored (NOTE: A101/A102/A104/A108 T1/E1 is treated as the same card).

PCISLOT

PCIBUS

FE_MEDIA

T1
E1

Front End Media type.

FE_LCODE

B8ZS
AMI
HDB3

T1
T1/E1
E1

Front End Line Coding.

FE_FRAME

ESF
D4
UNFRAMED
SLC-96
NCRC4
CRC4

T1
T1
T1/E1
T1
E1
E1

Front End Framing.

FE_LINE

Number

T1/E1

Front End Port/Line number.
(For A108, FE_LINE=1..8; for A104, FE_LINE=1..4)

TE_CLOCK

MASTER
NORMAL

T1/E1 clock source.
Normal - slave clock, clock is received from telco (default). Master- master clock, use HW oscillator clock.

TE_REF_CLOCK

Number

T1/E1 Reference clock source.
This options allows one to use the incoming clock from a different port as a clock source to this port. This option works only if TE_CLOCK is MASTER. If TE_REF_CLOCK is set to 0, the feature is disable.

TE_HIGHIMPEDANCE

YES
NO

Enable/Disable RX High Impedance mode.

TE_RX_SLEVEL

120
180
300
360
430
300
225
175
120

T1/E1:12dB
T1/E1:18dB
T1/E1:30dB
T1:36dB
E1:43dB
T1/E1:HI:30dB
T1/E1:HI:22.5dB
T1/E1:HI:17.5dB
T1/E1:HI:12dB

Define T1/E1 Receive sensitivity (Max Cable loss allowed) (dB). 
('HI' means that these options available if TE_HIGHIMPEDANCE parameter is set to YES).

LBO

0DB
7.5DB
15DB
22.5DB
0-110ft
110-220ft
220-330ft
330-440ft
440-550ft
550-660ft
120OH
75OH  

T1
T1
T1
T1
T1
T1
T1
T1
T1
T1
E1
E1

Define the Line Build Out

(LBO compensates for the loss in decibels based on the distance from the device to the first repeater in the circuit. A longer distance from the device to the repeater requires that the signal strength on the circuit be boosted to compensate for loss over that distance.)

FE_TXTRISTATE

YES
NO

Enable/Disable T1/E1 Tx Tri-State mode.

MTU

TDMV_SPAN

Number

Define span number for this device

TDMV_DCHAN

Number

Set to 0 if HW DCHAN is disabled. To enable HW DCHAN support, set it to dchan number

TDMV_HW_DTMF

YES
NO

Enable/Disable Hardware DTMF detection (Echo Cancellation module is required)

TDMV_HW_FAX_DETECT

YES
NO

 Enable/Disable Hardware Fax detection (Echo Cancellation module is required)

 TE_IGNORE_YEL

YES
NO

 Ignore incoming Yellow alarms and do not stop transmitting.  Needed for ATM systems where Yellows don't clear till cells are aligned

HWEC_CLKSRC

YES

Changes the port that will be used to recover a clock for the HWEC.  By default the first port started is used.
Placed in the wanpipeX.conf file that you wish to be the clock source.