Page Comparison

...

 Installation:

ADSL drivers are part of Wanpipe's DEFAULT installation.
eg:  ./Setup install  -> Default Compilation Mode

Configuration:

ADSL configuration is performed using /usr/sbin/wancfg GUI configurator.  Sample files are also located at the bottom of this file.

...

1. Interface Section

2. Specify interface name.
   (Leave it default)

3. Operation Mode: PPPoE
   PPPoE: This interface will be used by the PPPoE
               daemon, thus no ip information is needed.

4. Leave the rest of the option DEFAULT

5. End of configuration, exit and save

6. Download Roaring Penguin PPPoE Stack : 

rp-pppoe-3.4.tar.gz -  README 

1. Start Wanpipe:  

wanrouter start

2. Install and configure Roaring Penguin PPPoE Stack.

    Note: The ethernet interface name must be the wanpipe 
              pppoe interface name in section 5.1 above.

...

Check /var/log/messages.
...
w1g1: TTY Driver Init: Major 240, Minor Range 0-32
w1g1: TTY Sync Dev Minor 0 : /dev/ttyWP0   
...
or you might see the following depending on kernel used: 
---
w1g1: TTY Driver Init: Major 240, Minor Range 0-32
w1g1: TTY Sync Dev Minor 0 : /dev/ttyWP/0
---
Now the driver is ready for pppd connection.

7. Start PPPD based on configuration below:

pppd call isp_wanpipe1 <enter>
pppd call isp_wanpipe2 <enter>
...
For all wanpipe devices configured.

...

- /dev/ttyWPX             :X is TTY_MINOR number.
- /etc/ppp/options         
- /etc/ppp/peers/isp_wanpipeX     :X is a wanpipe device number (1-16)

2. Device /dev/ttyWP(0,1,2..)

To interface a PPPD daemon to the WANPIPE TTY driver a 
/dev/ttyWPX X={0,1,3...) device must be created.
eg: 
mknod -m 666 /dev/ttyWP0 c 240 0
mknod -m 666 /dev/ttyWP1 c 240 1
mknod -m 666 /dev/ttyWP2 c 240 2 
...
Note: 240 is the Major Number and 0,1,2... are the Minor Numbers

3. File /etc/ppp/options

-------CUT HERE ----------------------
persist            #If connection goes down try to connect again
defaultroute   #This interface will set default route
asyncmap 0
sync                #Use Synchronous PPP 
lcp-echo-interval 5
lcp-echo-failure 12

#Following options disable compression.
#Lot of Telco equipment doesnt support it
nobsdcomp
nodeflate
nopcomp
novj
novjccomp
noaccomp -am

#silent          #On some CISCO routers we must be in silent mode
nodetach     #DEBUG Should be commented out in production
debug          #Should be commented out in production
kdebug 2      #Should be commented out in production
-------CUT HERE ----------------------

4. File /etc/ppp/peers/isp_wanpipeX (X=1 to 16)

-------CUT HERE----------------------
ttyWP0          #Bind to WANPIPE device wanpipe1

#If IP address is commented out PPPD will attempt to
#get the IP address dynamically. 
#Some PPP servers only negotiate single IP p-to-p address
#in such cases one must specify a their own Local:PtoP IP addresses.
#1.1.1.1:1.1.1.2         

#Set user name and password if running with PAP/CHAP
#Uncomment next two parameters if needed
#user <username>
#password <password>

-------CUT HERE----------------------

5. For more information on PPPD configuration view 

README.pppd

...

Multilink-PPP (PPPoA) over ADSL using PPPD Daemon

...

- /dev/ttyWPX             :X is TTY_MINOR number.
- /etc/ppp/options         
- /etc/ppp/peers/isp_wanpipeX     :X is a wanpipe device number (1-16)

2. Device /dev/ttyWP(0,1,2..)

To interface a PPPD daemon to the WANPIPE TTY driver a 
/dev/ttyWPX X={0,1,3...) device must be created.
eg: 
mknod -m 666 /dev/ttyWP0 c 240 0
mknod -m 666 /dev/ttyWP1 c 240 1
mknod -m 666 /dev/ttyWP2 c 240 2 
...
Note: 240 is the Major Number and 0,1,2... are the Minor Numbers

3. File /etc/ppp/options

-------CUT HERE ----------------------
persist            #If connection goes down try to connect again
defaultroute   #This interface will set default route
asyncmap 0
sync                #Use Synchronous PPP 

lcp-echo-interval 1
lcp-echo-failure 3
 
#Following options disable compression.
#Lot of Telco equipment doesnt support it
nobsdcomp
nodeflate
nopcomp
novj
novjccomp
noaccomp -am

multilink       #Enable Multilink

#silent          #On some CISCO routers we must be in silent mode
#nodetach     #DEBUG Should be commented out in production
#debug          #Should be commented out in production
#kdebug 2      #Should be commented out in production
-------CUT HERE ----------------------

4. File /etc/ppp/peers/isp_wanpipeX (X=1 to 16)

-------CUT HERE----------------------

ttyWP0          #Bind to WANPIPE device wanpipe1

#If IP address is commented out PPPD will attempt to
#get the IP address dynamically. 
#Some PPP servers only negotiate single IP p-to-p address
#in such cases one must specify a their own Local:PtoP IP addresses.
#1.1.1.1:1.1.1.2       

#MULTILINK NOTE: 
#Each peer interface must have same IP configuration

#Set user name and password if running with PAP/CHAP
#Uncomment next two parameters if needed
#user <username>
#password <password>

-------CUT HERE----------------------

5. For more information on PPPD configuration view 

README.pppd

6. Start PPPD based on configuration above:

pppd call isp_wanpipe1 <enter>
pppd call isp_wanpipe2 <enter>
...
For all wanpipe devices configured.
Where isp_wanpipe1 is the master device that contains IP information, and the rest of wanpipe devices have "noip" config options in peers/isp_wanpipeX filex.

...

[w1ad]

---- CUT HERE -----

...

Protocols supported on Windows

...