IMG 1010 - Adding a VoIP Module
Installing a VoIP or Media Module (IMG 1010)
Follow the procedure below to add a VoIP or Media module on the IMG.
Warning! Ensure that the system is disconnected from its power source and from all telecommunications links, networks, or modem lines whenever the chassis cover is removed. Do not operate the system with the cover removed.
Avertissement! Assurez-vous que le système soit débranché de son alimentation ainsi que de toutes les liaisons de télécommunication, des réseaux, et des lignes de modem avant d'enlever le capot. Ne pas utiliser le système quand le capot est enlevé.
Warnug! Das System darf weder an eine Stromquelle angeschlossen sein noch eine Verbindung mit einer Telekommunikationseinrichtung, einem Netzwerk oder einer Modem-Leitung haben, wenn die Gehäuseabdeckung entfernt wird. Nehmen Sie das System nicht ohne die Abdeckung in Betrieb.
Avvertenza! Prima di rimuovere il coperchio del telaio, assicurarsi che il sistema sia scollegato dall.alimentazione, da tutti I collegamenti di comunicazione, reti o linee di modem. Non avviare il sistema senza aver prima messo a posto il coperchio.
¡Advertencia! Asegúrese de que cada vez que se quite la cubierta del chasis, el sistema haya sido desconectado de la red de alimentación y de todos lo enlaces de telecomunicaciones, de red y de lÃneas de módem. No ponga en funcionamiento el sistema mientras la cubierta esté quitada.
The procedures below assumes a familiarity with the general terminology associated with electronic equipment and with safety practices and regulatory compliance required for using and modifying electronic equipment.
The procedures below should be performed by qualified technical personnel only. Â
Unplug the equipment before performing the procedures described below. Failure to disconnect the power before opening the chassis can result in personal injury or equipment damage.
The power supply in this product contains no user-serviceable parts. Refer servicing to qualified technical personnel only.
Required Tools and Parts
Caution: Electrostatic Discharge Protection (EDP) must always be used. Electrostatic Discharge (ESD) protective straps, shoes, or mats must be used when working with electronic components. Electrostatic discharge from your body can damage integrated circuits during installation.
VoIP module or Media module (Sangoma supplied).
4 Phillips pan head screws (Sangoma supplied).
#1 Phillips head screwdriver (customer supplied).
Procedure
Set power to OFF (O) at rear of docking station.
Remove Motherboard Tray. See Diagram 1 - Removing Motherboard Tray.
Loosen the two ejector captive fasteners located on each side of the front panel.
Lift the ejectors upward and pull to unseat the tray from the docking station.
Slide the tray out.
Locate Module Position. See Diagram 2 - Module Positions.
Install module on motherboard.
the module over the four standoffs.
Align the connectors on the module with the connectors on the motherboard and press together.Â
Cautions
The connectors must be properly aligned and fully seated, to ensure a trouble-free installation.
When pressing the module onto the motherboard do not press on the components installed on the module, but rather press on an open area on the edge of the Printed Circuit Board itself.
Attach the module with the four (4) Phillips pan head screws.
Re-insert Motherboard Tray
Align the rail on each side of the tray with the guides on the inside of the docking station.
Ensure the ejectors are in the up position.
Slide the tray in until the power connectors and signal connectors initially mate (the ejectors will start to move down).
Do not force the tray if any resistance occurs when mating with the docking station. Using undue force could damage the unit.
The guides only provide gross alignment to the power and signal connectors. The guide pins on the main board and I/O card are self-aligning and provide exact alignment for the connectors.
The tray guides also act as the conduit for any Electrostatic Discharge (ESD) as the tray initially mates with the docking station.
When the tray is seated and the connectors are mated, push the ejectors down and tighten captive fasteners.
Set power to ON (1) at rear of docking station.
Configure Module.Â
See procedure below to configure modules:
IMG 1010 - Configuring Media to Play a Treatment
 Â
Diagram 1 - Removing Motherboard Tray
Â
Diagram 2 - Module Positions
Â
Â