Versions Compared

Version Old Version 1 New Version 2
Changes made by

Nathaniel Halbrooks

Nathaniel Halbrooks

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

CyberData Call Button V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

...

  1. Image Added

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Ceiling Speaker V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Emergency Indoor Intercom V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

    Image RemovedCyberdata-17.jpgImage Added

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

    Image RemovedImage Added

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Indoor Intercom V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

    Image RemovedImage Added

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Indoor Keypad Intercom V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

    Image RemovedImage Added

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Office Ringer V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Outdoor Intercom V2 & V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

    Image RemovedImage Added

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Outdoor Keypad Intercom V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

    Image RemovedImage Added

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Adapter V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Gateway V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Server V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Amplifier V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the Test/Reset switch while the unit beeps after one second and all indicator lights on the front of the unit come on.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Strobe V2

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Talkback Ceiling Speaker V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Zone Controller V3

...

How to Find the IP Address

...

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, you should see the MAC Address under “Current Settings.”

    Image RemovedImage Added

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

    Image RemovedImage Added

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

...