Updating Firmware

Current Firmware versions

The table below lists the current firmware available for all telephony Cards.

AFT Card Model	Firmware version	Change Log	Release Date
T116	v01, v01-base	More Info	(2012-12-31)
A116	v44	More Info	(2012-05-14)
A108	v44	More info	(2010-08-24)
A104	v45	More info	(2014-05-09)
A102	v40	More info	(2014-05-09)
A101	v40	More info	(2014-05-09)
A200	v13	More info	(2009-12-10)
A400	v11	More info	(2008-07-10)
A104(pmc framer)	v26	More info	(2007-07-10)
A301	v11	More info	(2007-07-10)
A14X	v08	More info	(2008-10-28)
A500	v35	More info	(2009-04-30)
A056	v01
B600 (cannot be updated)	v03	More Info	(2009-05-08)
B601	v04	More info	(2009-05-08)
B500	v44	More Info	(2012-09-07)
B700	v35	More Info	(2009-07-03)
U100	v21	More Info	(2009-09-11)

Archived firmware files: ftp.sangoma.com/firmware

Identifying the firmware version on your Telephony card

To identify which firmware version your Telephony Card has type the following command in your Linux command line:

-> wanrouter hwprobe

Below is an example out of the command 'wanrouter hwprobe' for a system that has a Sangoma 8-port A108 card installed.

wanrouter hwprobe

AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=1 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=2 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=3 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=4 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=5 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=6 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=7 : HWEC=256 : V=44
AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=14 : CPU=A : PORT=8 : HWEC=256 : V=44

As seen from the above output, the firmware version of this card is 44 (as indicated by V=44).
This card has the most current available firmware and does not require a firmware update.

If your telephony card requires a firmware update, please choose one of the following instructions

Upgrading firmware on your FreePBX Distro System

The following applies to all binary distributions (i.e FreePBX, Elastix...)

To upgrade the firmware on your FreePBX system, you will need to shut down your production environment and allow for 30 seconds to 1 minutes for the process to complete.

Type the following in your Linux command line

Stop Asterisk
- amportal stop (For FreePBX 12 and below)
- fwconsole stop (For FreePBX 13 and above)
Stop the Sangoma Telephony driver (which is called 'Wanpipe')
- wanrouter stop
Being the firmware update process
1. Navigate to the following directly by typing:
  -> cd /etc/wanpipe/util/wan_aftup/
2. Type the following command to run the upgrade
  -> ./update_aft_firm.sh
  You will notice an output similar to the example below (dependent on the telephony cards installed)
```
[root@support-sys1 wan_aftup]# ./update_aft_firm.sh
modprobe wan_aften  > /dev/null
AFT card enabled
 
 
Sangoma AFT Series card update flash software (version 1.9)
 
 
Sangoma AFT card list:
 w1g1: AFT-A108-SH : SLOT=2 : BUS=7 : IRQ=23 : CPU=A : PORT=1 : HWEC=256 : V=42 (Ver.42)
 
 
Please select card interface [def=w1g1; q=exit] >
```
3. specify the interface name that corresponds to your card, based on the output.
  i.e. w1g1 then press <enter>
4. A list of available firmware versions will be presented. Select the latest/current firmware version, as referenced from the table at the beginning of this page.
  Example:
```
Please select card interface [def=w1g1; q=exit] > w1g1
List of available versions:
         Version no. 44 (filename=A108dm_0100_V44.BIN)
Please specify version number [def=44; q=exit] > 44
```
  If the list does not display the latest/current firmware that is seen in the table, you will need to upload the latest/current firmware file into your system and redo these steps.
  To do this:
  a. Right click on the firmware file in the table, located under the 'Firmware version' column and copy the link . This will copy a link to the location of that firmware file.
  b. In you Linux command line, in the current directory of /etc/wanpipe/firmware/wan_aftup, type:
  -> 'wget' then left click to paste the firmware file location.
  i.e. wget https://ftp.sangoma.com/firmware/A108dm_0100_V44.BIN
  -> This will auto download the firmware, assuming your system has internet access
  c. now follow the steps again
5. After pressing <enter> the upgrade process will begin
  Example:
```
Please specify version number [def=44; q=exit] > 44
ABOUT TO board_reset
FINISH  board_reset
w4g1: Current Sangoma Flash: Revision=44 ID=0x205B
        Erasing sectors                         Passed
        Updating flash                          1%
```
Now that the firmware on your card has been updated, start your production environment back up.
1. Type the following, in your Linux command line, to start the telephony driver:
  -> wanrouter start
2. Start Asterisk by typing:
  -> amportal start (For FreePBX 12 and below)
  -> fwconsole start (For FreePBX 13 and above)

All done!

Upgrading firmware on your manually compiled Linux (Asterisk/FreeSWITCH/NSG-SS7) system

To upgrade the firmware on your Linux system, you will need to shut down your production environment and allow for 30 seconds to 1 minutes for the process to complete.