A30 TXT Configuration 1.4.5.1

Version

String

If the phone is configured for auto provisioning and it successfully loads this configuration, the version string will be displayed on-screen.

WAN TYPE

Integer, 0-2, Defaults to 0

Defines the type of networking, 0 (IPv4 Only), 1 (IPv6 Only), 2 (IPv4 & IPv6)

WAN IP

IPv4 address

Sets the IPv4 address of the phone.

WAN Subnet Mask

IPv4 net mask

Sets the IPv4 net mask of the phone.

WAN Gateway

IPv4 network gateway

Sets the IPv4 default gateway / route of the phone.

Domain Name

Domain name, as string

Sets the default domain search name of the phone.

Primary DNS

IPv4 address

Sets the primary DNS server of the phone.

Secondary DNS

IPv4 address

Sets the secondary DNS server of the phone.

Enable DHCP

Boolean, Defaults to 1

Enables or disables DHCP network configuration request. Defaults to 1.

DHCP Auto DNS

Boolean, Defaults to 1

Configures the phone to accept DNS servers provided by DHCP. If disabled, the phone will use the DNS servers defined by the PrimaryDNS and SecondaryDNS net configuration elements. Defaults to 1.

DHCP Auto Time

Boolean, Defaults to 1

Configures the phone to set its time and SNTP server based upon receipt of DHCP Option 42. If disabled, the phone will use the NTP server as defined by the SNTPServer date configuration element and time as defined in other date configuration elements. Defaults to 1.

Use Vendor Class ID

Boolean, Defaults to 0

Configures the phone to send DHCP Option 61, Vendor Class Identifier. Defaults to 0.

Enable PPPoE

Boolean, Defaults to 0

Configures the phone to perform PPPoE authentication in order to retrieve its network configuration. Defaults to 0

PPPoE User

String

If the phone is to use PPPoE authentication, sets the PPPoE authentication username.

PPPoE Password

String

If the phone is to use PPPoE authentication, sets the PPPoE authentication password.

ARP Cache Life

Time, in minutes, Defaults to 2

Specifies the time in minutes to cache ARP

WAN6 IP

IPv6 IP Address

Specifies the phone's IPv6 address

WAN6 IP PREFIX

IPv6 IP Address Prefix

Specifies the phone's IPv6 address prefix

WAN6 Gateway

IPv6 Address

Specifies the phone's IPv6 gateway

Domain6 Name

String

Specifies the IPv6 domain name search

Primary DNS6

IPv6 Address

Specifies the IPv6 primary DNS server address

Secondary DNS6

IPv6 Address

Specifies the IPv6 secondary DNS server address

Enable DHCP6

Boolean, Defaults to 1

If enabled, directs the phone to use a DHCPv6 server for IPv6 address assignment

DHCP6 auto DNS

Boolean Defaults to 1

If enabled, directs the phone to retrieve DNS servers from the DHCPv6 server

DHCP6 Auto Time

Boolean Defaults to 0

If enabled, directs the phone to retrieve its SNTP server from the DHCPv6 server

Use Vendor6 Class ID

Boolean, Defaults to 0

If enabeld, the phone will send vendor class ID to the DHCPv6 server

Vendor6 Class ID

String

Specifies the phone's DHCPv6 vendor class ID

WIFI Enable

Boolean, Defaults to 0

Enables or disables support for WiFi network connectivity. Currently unused.

G723 Bit Rate

Boolean, Defaults to 1

Sets the bitrate type to be used for G.723.1 voice codec encoding. 0 sets encoding to 5.3kbit/s. 1 sets encoding to 6.3kbit/s. Defaults to 1

ILBC Payload Type

Integer, Defaults to 97.

Sets the RTP payload type to be used for iLBC voice codec encoding. Defaults to 97.

ILBC Payload Len

20, 30

Sets the iLBC voice codec block length duration in milliseconds. 20 sets 20ms. 30 sets 30ms. Defaults to 20.

AMR Payload Type

Integer, Defaults to 108

Sets the RTP payload type to be used for AMR voice codec encoding. Defaults to 108.

AMRWB Payload Type

Integer, Defaults to 109

Sets the RTP payload type to be used for AMR (G.722.2) voice codec encoding. Defaults to 109.

Dtmf Payload Type

Integer, Defaults to 101

Sets the RTP payload type to be used for RFC2833 DTMF events. Defaults to 101.

Opus Payload Type

Integer, Defaults to 107

Sets the RTP payload type to be used for Opus voice codec encoding. Defaults to 107

Opus Sample Rate

Boolean, Defaults to 0

Sets the Opus voice codec encoding type. 0 sets Narrowband. 1 sets Wideband. Defaults to 0.

VAD

Boolean, Defaults to 0

Enables or disables Voice Activity Detection (VAD) for certain (G.729) codecs. Defaults to 0.

H264 Payload Type

Integer, Defaults to 117

Sets the RTP payload type to be used for H.264 video codec encoding. Defaults to 117

Resv Audio Band

Boolean, Defaults to 0

If enabled, the phone will reduce video bandwidth to prioritize audio. Defaults to 0.

RTP Initial Port

Integer, Defaults to 10000

Sets the starting RTP port used for calls. Defaults to 10000

RTP Port Quantity

Integer, Defaults to 200

Sets the number of RTP ports to span across before recycling. Defaults to 1000.

RTP Keep Alive

Boolean, Defaults to 0

Enables or disables the sending of a periodic RTP keep alive packet. Defaults to 0.

RTCP CNAME User

String

Sets the RTCP CNAME User part for RTCP Sender reports generated by the phone.

RTCP CNAME Host

String

Sets the RTCP CNAME Host part for RTCP Sender reports generated by the phone.

Select Your Tone

Integer, Defaults to 11

Sets the phone's default tones based upon country as follows:

Australia, 15
Austria, 22
Belgium, 0
Brazil, 16
Canada, 18
Chile, 20
China, 1
Croatia, 17
Czech Republic, 12
Denmark, 23
Finland, 24
France, 25
Germany, 2
Greece, 26
Hungary, 27
India, 29
Israel, 3
Italy, 21
Japan, 4
Lithuania, 28
Mexico, 30
New Zealand, 31
Netherlands, 5
Norway, 6
Portugal, 32
Russia, 19
South Africa, 14
South Korea, 7
Spain, 33
Sweden, 8
Switzerland, 9
Taiwan, 10
United Kingdom, 13
United States, 11

Sidetone GAIN

Boolean, Defaults to 1

If enabled, the phone will provide sidetone

Play Egresss DTMF

Boolean, Defaults to 0

Currently unused

Dial Tone

String

Sets the dialing tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.

350+440/0

Ringback Tone

String

Sets the ring back tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.
440+480/2000,0/4000

Busy Tone

String

Sets the ring back tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.
480+620/500,0/500

Congestion Tone

String

Sets the congestion tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Call waiting Tone

String

Sets the call waiting tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.
440/300,0/10000,440/300,0/10000,0/0

Holding Tone

String

Sets the holding tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Error Tone

String

Sets the error tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Stutter Tone

String

Sets the stutter tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Information Tone

String

Sets the information tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Dial Recall Tone

String

Sets the dial recall tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.

350+440/100,0/100,350+440/100,0/100,350+440/100,0/100,350+440/0

Message Tone

String

Sets the message tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Howler Tone

String

 Sets the howler tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Number Unobtainable

String

Sets the number unobtainable tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.

400/500,0/6000

Warning Tone

String

Sets the warning tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.

1400/500,0/0

Record Tone

String

Sets the record tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones, e.g.

440/500,0/5000

Auto Answer Tone

String

Sets the auto answer tone pattern, as a tone or combination of tones with a defined duration, optionally followed by other tones.

Audio Codec Sets

Comma-separated list of:

PCMU
PCMA
G726-32
G729
G723
iLBC
AMR
AMR-WB 
opus
G722

Sets the list of codecs the phone is allowed to transcode.

Video Codec Sets

H264

Sets the video codec the A30 is allowed to decode.

Video Frame Rate

Integer, Defaults to 25

Sets the frame rate the A30 should expect to decode.

Video Bit Rate

Integer, Defaults to 2000000

Sets the bitrate of the video the A30 should expect to decode.

Video Resolution

Integer, Defaults to 4

Sets the resolution of the video the A30 should expect to decode.

Video Negotiate Dir

Integer, Defaults to 2

Currently Unused

SIP Port

Integer, 1-65535

Sets the local SIP signaling port used by the phone. Defaults to 5060

STUN Server

IPv4 address or hostname

Sets the IPv4 address or hostname of a remote STUN server to be used by the phone. Defaults to none.

STUN Port

Integer, 1-65535

Sets the port of the remote STUN server to be used by the phone. Defaults to none

STUN Refresh Time

Integer, in seconds

Sets the STUN server refresh period used by the phone. Defaults to 50.

SIP Wait Stun Time

Integer, in milliseconds

Sets the amount of the, in milliseconds, the phone should wait for the STUN server to respond before continuing.

Extern NAT Addrs

IPv4 address

If the phone is configured to use STUN, the SIP Contact address will be set according to this option. IP address of the phone, as broadcast by an upstream NAT router.

Reg Fail Interval

Integer, in seconds

Sets the time, after a failed registration, after reaching the halfway point of this interval time, at which the phone will attempt registration again. Defaults to 32.

SIP Pswd Encryption

Boolean, Defaults to 0

If enabled, passwords contained in exported phone configurations will be disguised. Defaults to 0.

Strict BranchPrefix

Boolean, Defaults to 0

If enabled, when the phone receives a SIP message with a branch field that does not begin with z9hG4bk, the phone will return a 4xx message. Defaults to 0

Video Mute Attr

Boolean, Defaults to 0

If enabled, causes the phone, when placing a video-enabled call on hold, to use the "inactive" SDP a-line parameter. If disabled, the phone will use the sendrecv parameter instead. Defaults to 0

Enable Group Backup

Boolean, Defaults to 0

If enabled, and the phone has both regular and backup registrars configured, the phone will, upon a failure to register with either of the registrars, unregister from both. If disabled, the phone will attempt to register with both, and the registration of one will not affect the registration with another. Defaults to 0.

Enable RFC4475

Boolean, Defaults to 0

If enabled, and the phone receives a SIP message with a From or To field containing a blank space, quotation marks, or both, the phone will reject the message. Defaults to 0.

Strict UA Match

Boolean, Defaults to 0

If enabled, the phone will only respond to requests from servers to which it is registered, based on the user-agent string provided by the incoming request. Defaults to 0.

CSTA Enable

Boolean, Defaults to 0

Enables or disables the phone's support of uaCSTA. Defaults to 0.

Notify Reboot

Boolean, Defaults to 0

If enabled, the phone will reboot in response to a received check-sync Event.

Phone Number

String

Sets the identifier used for the user part of the From and To lines in the phone's SIP messaging.

Display Name

String

Sets the quoted string name identifier used in the From and To (REGISTER only) in the phone's SIP messaging.

Sip Name

String

Sets a name for the SIP line, visible within the web admin UI of the phone.

Register Addr

IPv4 address or hostname

Sets the IPv4 address or hostname of the SIP Registrar.

Register Port

Integer, 1-65535

Sets the port used to contact the SIP Registrar. Defaults to 5060

Register User

String

Sets the SIP authentication user.

Register Pswd

String

Sets the SIP authentication password.

Register TTL

Integer, in seconds, Defaults to 3600

Sets the default Expires timer for SIP registration. Defaults to 3600.

Enable Reg

Boolean, Defaults to 0

Enables or disables SIP registration for this line.

Proxy Addr

IPv4 address or hostname

Sets the IPv4 address or hostname for the SIP Proxy. Defaults to none.

Proxy Port

Integer, 1-65535

Sets the port used to contact the SIP Proxy. Defaults to 5060.

Proxy User

String

Sets the SIP proxy authentication user.

Proxy Pswd

String

Sets the SIP proxy authentication password.

BakProxy Addr

IPv4 address or hostname

Sets the IPv4 address or hostname for the backup SIP Proxy. Defaults to none.

BakProxy Port

Integer, 1-65535

Sets the port used to contact the backup SIP Proxy. Defaults to 5060.

Enable Failback

Boolean, Defaults to 0

Sets whether the phone, whereby it is configured with both a primary and a backup proxy, should, whereupon detection that the primary proxy is operational again after having previously failed, resume sending calls to the primary server. If enabled, the phone will switch back to the primary proxy. If disabled, the phone will continue to send calls to the backup. Defaults to 0.

Signal Crypto

Boolean, Defaults to 0

If enabled, causes the phone to encrypt SIP signaling. Defaults to 0.

SigCrypto Key

String

Sets the key used to encrypt SIP signaling.

Media Crypto

Boolean, Defaults to 0

If enabled, causes the phone to encrypt RTP media. Defaults to 0.

MedCrypto Key

String

Sets the key used to encrypt RTP media.

SRTP Auth-Tag

Intege, Defaults to 0

If set to 0, the phone will utilizes 80 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_80. If set to 1, the phone will utilize 32 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_32. Defaults to 0.

Local Domain

Strings

Sets the domain name used in SIP registration

Always FWD

Boolean, Defaults to 0

If enabled, the phone will unconditionally forward calls. Defaults to 0.

Busy FWD

Boolean, Defaults to 0

If enabled, the phone will forward calls whenever it is busy. Defaults to 0.

No Answer FWD

Boolean, Defaults to 0

If enabled, the phone will forward calls that are not answered. Defaults to 0.

Always FWD Num

String

Sets the forwarding number used in conjunction with the AlwaysFWD option.

Busy FWD Num

String

Sets the forwarding number used in conjunction with the BusyFWD option.

NoAnswer FWD Num

String

Sets the forwarding number used in conjunction with the NoAnswerFWD option.

FWD Timer

Integer, in seconds, Defaults to 5

Sets the time, in seconds, applied to the NoAnswerFWD option. Defaults to 5.

Hotline Num

String

Sets the number to be dialed when the off-hook time is greater than the WarmLineTime and EnableHotline is enabled.

Enable Hotline

Boolean, Defaults to 0

If enabled, and the phone has been off-hook longer than the WarmLineTime, the phone will automatically dial the number defined by HotlineNum.

WarmLine Time

Integer, in seconds, 0-9, Defaults to 0.

Sets the amount of time the phone must remain off-hook before attempting to execute Hotline functionality.

Pickup Num

String

Sets the dialing prefix applied to calls that are picked up using function keys configured for Pickup functionality.

Join Num

String

Sets the dialing prefix applied to calls that are joined using function keys configured for Join functionality.

Ring Type

Integer, 1-9, Defaults to 1

Sets the default ringing type to be used. Defaults to 1.

NAT UDPUpdate

Integer, 0-2, Defaults to 1

If set to 1, the phone will send SIP OPTION packets to the server after each UDPUpdate_TTL time.  If set to 2, the phone will send a CRLF to the server after each UDPUpdate_TTL time.  If set to 0, the phone will send nothing.  Defaults to 1.

UDPUpdate TTL

Integer, in seconds, Defaults to 60

Sets the timer used by the NATUDPUpdate option.

Server Type

Integer

Sets special compatibility settings required for specific server types. The following types are supported:

3CX - 31
BOTE - 6
BroadSoft - 28
Cellcom - 30
COMMON - 0
CONFIG - 23 
FUJITSU - 24
Karel UCAP - 29
MITEL - 17
MS_RP - 22
NET2PHONE - 1
NORTEL - 14
SOFTX3000 - 26

Defaults to 0. 

User Agent

String

Sets the SIP User-Agent passed by the phone when communicating. SHOULD THIS DEFAULT TO A30?

PRACK

Boolean, Defaults to 0

Enables or disables SIP PRACK functionality within the phone. Defaults to 0.

Keep AUTH

Boolean, Defaults to 0

If enabled, the phone will, on SIP re-registration, send authentication in the initial REGISTER rather than waiting to send it after receiving a 401 Unauthorized message. Defaults to 0.

Session Timer

Boolean, Defaults to 0

If enabled, the phone will send SIP session timers throughout the call, ending the call when there is no reply. Defaults to 0.

S Timer Expires

Integer, in seconds

Sets the SIP Session timer timeout value in seconds.

Enable GRUU

Boolean, Defaults to 0

If enabled, the phone will append GRUU information to the Contact header of INVITEs. Defaults to 0.

DTMF Mode

Integer, 0-3, Defaults to 3

Sets the DTMF method to be used by the phone, as follows:

Inband - 0
RFC2833 - 1
SIP INFO - 2
Auto - 3 

DTMF Inf oMode

Integer, 0-1, Defaults to 0

If set to 1, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send "*" and "#" respectively. If set to 0, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send as 10 and 11 respectively. Defaults to 0.

NAT Type

Boolean, Defaults to 0

If enabled, STUN will be used. Defaults to 0.

Enable Rport

Boolean, Defaults to 0

If enabled, the phone will send rport to assist with NAT traversal as per RFC3581. Defaults to 0.

Subscribe

Boolean, Defaults to 0

If enabled, the phone will subscribe for Message Waiting Indicator (MWI). Defaults to 0.

Sub Expire

Integer, in seconds, Defaults to 3600

The timer at half-of-which, the phone will re-subscribe. Defaults to 3600.

Single Codec

Boolean, Defaults to 0

If enabled, the phone will respond to SIP messages with only one codec, rather than with all codec capabilities. Defaults to 0.

CLIR

Integer, Defaults to 0

Specifies the method of anonymous calling to use. When set to 0, the phone calls normally. When set to 1, the phone calls anonymously according to RFC3323. When set to 2, the phone calls anonymously according to RFC3325.

Strict Proxy

Boolean, Defaults to 0

When enabled, respond using the source address, not the Via address. Defaults to 0.

Direct Contact

Boolean, Defaults to 0

When enabled, attempt to directly communicate with the called party, not using the intermediary proxy or UA. Defaults to 0.

History Info

Boolean, Defaults to 0

When enabled, call history information for the line will be provided. Defaults to 0. This configuration item is currently unused.

DNS SRV

Boolean, Defaults to 0

If enabled, the phone will perform DNS SRV resolution for outgoing requests. Defaults to 0.

DNS Mode

Integer, 0-2, Defaults to 0.

Sets the type of host resolution to perform. When set to 0, the phone will use A records. When set to 1, the phone will use SRV records. When set to 2, the phone will use NAPTR records.

XFER Expire

Integer, Defaults to 0

Specifies the time, in seconds, after which the phone will send a BYE following attended transfer hang up.

Ban Anonymous

Boolean, Defaults to 0

When enabled, the phone will reject anonymous calls. Defaults to 0.

Dial Off Line

Boolean, Defaults to 0

If enabled, the phone will attempt to place outgoing calls, even when it is unregistered. If disabled, the phone will not be able to place outgoing calls when it is unregistered. Defaults to 0.

Quota Name

Boolean, Defaults to 0

If enabled, the phone will encapsulate the Display Name that it sends in SIP signaling inside of quotation marks. Defaults to 0.

Presence Mode

Boolean, Default to 0

When enabled, the phone utilizes special presence handling for Wuchuan servers. Defaults to 0.

RFC Ver

Integer, Defaults to 1

Specifies the SIP signaling RFC standard to utilize. When set to 0, the phone will communicate using RFC2543 compliant signaling. When set to 1, the phone will communicate using RFC3261 compliant signaling. Defaults to 1.

Phone Port

Unused

Unused

Signal Port

Integer, Defaults to 5060

Sets the phone's local SIP signaling port. Defaults to 5060.

Transport

Integer, 0, 1, 3, Defaults to 0

Sets the transport type for SIP signaling.

UDP - 0
TCP - 1
TLS - 3 

Use SRV Mixer

Boolean, Defaults to 0

When enabled, the phone utilizes server-side conferencing support. Defaults to 0.

SRV Mixer Uri

String

Sets the URI to be used for server-side conferencing when the UseSRVMixer option is enabled.

Long Contact

Boolean, Defaults to 0

If enabled, allows the phone to process long Contact fields. Defaults to 0.

Auto TCP

Boolean, Defaults to 0

When enabled, if the packet size of a UDP signaling packet is to exceed 1300 bytes, automatically use TCP transport. Defaults to 0.

Uri Escaped

Boolean, Defaults to 1

If disabled, the phone will not escape # characters into "%23" when creating URIs. While this option is enabled, the rule to send numbers when pressing the # key should be disabled.

Click to Talk

Boolean, Defaults to 0

If enabled, the phone can make a call by itself receiving an incoming REFER message. Defaults to 0.

MWI Num

String

Sets the number to dial for voicemail.

CallPark Num

String

Sets the number to dial for call parking.

Retrieve Num

String

Sets the number to dial for call retrieval for Broadsoft environments.

MSRPHelp Num

String

For MS_RP_BU servers, sets a number to be called after a successful transfer.

User Is Phone

Boolean, Defaults to 1

If disabled, the phone will not append the ";user=phone" parameter to SIP messages.

Auto Answer

Boolean, Defaults to 0

If enabled, and if the NoAnswerTime has elapsed, the phone will automatically answer an incoming call. Defaults to 0.

NoAnswerTime

Integer, in seconds, defaults to 5

Sets the amount of time, in seconds, the phone should wait on an incoming call before proceeding to AutoAnswer, if AutoAnswer is enabled. Defaults to 5.

MissedCallLog

Boolean, Defaults to 1

If disabled, the phone will not record call logs for this SIP line. Defaults to 1.

SvcCode Mode

Boolean, Defaults to 0

If enabled, the phone will allow the sending of service codes (numbers) to the SIP server, depending on the enabling/disabling of certain functions on the phone. Defaults to 0.

DNDOn SvcCode

String

Sets the number to send to the server when DND is enabled on the phone.

DNDOff SvcCode

String

Sets the number to send to the server when DND is disabled on the phone.

CFUOn SvcCode

String

Sets the number to send to the server when Call Forward Unconditional is enabled on the phone.

CFUOff SvcCode

String

Sets the number to send to the server when Call Forward Unconditional is disabled on the phone.

CFBOn SvcCode

String

Sets the number to send to the server when Call Forward Busy is enabled on the phone.

CFBOff SvcCode

String

Sets the number to send to the server when Call Forward Busy is disabled on the phone.

CFNOn SvcCode

String

Sets the number to send to the server when Call Forward on No Answer is enabled on the phone.

CFNOff SvcCode

String

Sets the number to send to the server when Call Forward on No Answer is disabled on the phone.

ANCOn SvcCode

String

Sets the number to send to the server when Anonymous Call Banning is enabled on the phone.

ANCOff SvcCode

String

Sets the number to send to the server when Anonymous Call Banning is disabled on the phone.

Send ANOn Code

String

Sets the number to send to the server when Anonymous Calling is enabled on the phone.

Send ANOff Code

String

Sets the number to send to the server when Anonymous Calling is disabled on the phone.

CW On Code

String

Sets the number to send to the server when Call Waiting is enabled on the phone.

CW Off Code

String

Sets the number to send to the server when Call Waiting is disabled on the phone.

VoiceCodecMap

Comma-separated list of:

PCMU
PCMA
G726-32
G729
G723
iLBC
AMR
AMR-WB 
opus
G722

Sets the voice codecs used for this line.

VideoCodecMap

H264

Sets the video codecs used for this line.

BLFList Uri

String

Specifies the BLF Resource List to which the phone should subscribe. Multiple lists are supported, separated by commas.

BLF Server

IPv4 address or Hostname

If the server to which the phone is registered does not support BLF Resource List subscription package, sets the address of the BLF Resource List server.

Respond 182

Boolean, Defaults to 0

If enabled, the phone will, when it's already on call and an additional call comes in, send a 182 Queued SIP message to the SIP server. If disabled, the phone sends a 180. Defaults to 0.

Enable BLFList

Boolean, Defaults to 0

If enabled, the phone will subscribe for BLF Resource List.

Caller Id Type

Integer, 1-5, Defaults to 1

Sets the priority of the incoming Caller ID:

FROM header - 1
P-Asserted-Identity header, followed by FROM header - 2
Remote-Party-ID header, followed by FROM header - 3
P-Asserted-Identity header, followed by Remote-Party-ID header, followed by FROM header - 4
Remote-Party-ID header, followed by P-Asserted-Identity-Header, followed by FROM header - 5

Syn Clock Time

Boolean, Defaults to 0

If enabled, the phone will set its clock according to the Date field in the 200 OK following a successful REGISTER. Defaults to 0.

Use VPN

Boolean, Defaults to 1

If disabled, and the phone is connected to a VPN, the phone will not initiate REGISTER using the VPN IP address. If enabled, the phone will, when connected to a VPN, use the VPN IP address to initiate the REGISTER. Defaults to 1.

Enable DND

Boolean, Defaults to 0

If enabled, the phone will not accept incoming calls from this SIP line. Defaults to 0.

Inactive Hold

Boolean, Defaults to 0

If enabled, the phone will send "a=inactive" in the INVITE sent after a call is placed on hold. If disabled, the phone will send "a=sendonly" in the INVITE sent after a call is placed on hold. Defaults to 0.

Req With Port

Boolean, Defaults to 0

If disabled do not send port in SIP messages to the server.

Update Reg Expire

Boolean, Defaults to 1

If disabled, the phone will not update its registration expiration with the Expires value from the 200 OK that the server sends in response to a successful registration. Defaults to 1.

Enable SCA

Boolean, Defaults to 0

Enables support for the Broadsoft SCA feature. Defaults to 0.

Sub CallPark

String

Sets the Call Parking subscribed number for Broadsoft servers.

Sub CC Status

Boolean, Defaults to 0

If enabled, subscribes to the Broadsoft call center service. Defaults to 0.

Feature Sync

Boolean, Defaults to 0

Enables support for Broadsoft Feature Sync. Defaults to 0.

Enable XferBack

Boolean, Defaults to 0

If enabled, when a call is transferred from another, and XferBackTime has been reached, the call will be transferred back to the original transferer. Defaults to 0.

XferBack Time

Integer, in seconds, Defaults to 35

Sets the amount of time, in seconds, that must elapse before EnableXferBack is processed.

Use Tel Call

Boolean, Defaults to 0

If enabled, the phone will replace "sip" in its URIs with "tel"

Enable Preview

Boolean, Defaults to 0

If enabled, video preview will be enabled for video received before answer.

Preview Mode

n/a

Currently unused.

TLS Version

Integer, 0-2, Defaults to 0

Sets the type of TLS protocol version to be used:

TLS 1.0 - 0
TLS 1.1 - 1
TLS 1.2 - 2 

CSTA Number

String

Sets the number/URI for the uaCSTA server.

Enable ChgPort

Boolean, Defaults to 0

If enabled, the phone will attempt to dynamically change its local SIP port in order to work around SIP Router ALG issues. Defaults to 0.

VQ Name

String

Sets an identifier for the voice quality server.

VQ Server

IPv4 Address or Hostname

Sets the IPv4 Address or hostname of the voice quality server.

VQ Server Port

Integer, 1-65535, Defaults to 5060

Sets the port used by the voice quality server.

VQ HTTP Server

URL

Sets the HTTP URL of the voice quality server.

Flash Mode

Integer, 0-1, Defaults to 0

If set to 0, flash is handled locally on the phone. If set to 1, the phone will send a SIP INFO message indicating the flash event to the server, with data defined by Content_Type and Content_Body

Content Type

String

Sets the content type data used when the phone sends SIP INFO flash messages to the server.

Content Body

String

Sets the body of the data used when the phone sends SIP INFO flash messages to the server.

Unregister On Boot

Boolean, Defaults to 0

If enabled, the phone will send unregisters to any registered servers after it reboots, before it attempts to register.  Defaults to 0.

Enable MAC Header

Boolean, Defaults to 0

If enabled, the phone will include a MAC parameter, with MAC address as value, in SDP.

Enable Register MAC

Boolean, Defaults to 0

If enabled, the phone will include a MAC parameter, with MAC address as value, in SIP REGISTER packets.

Record Start

Record:on

Specifies the SDP to be passed when recording is started. Currently unused.

Record Stop

Record:off

Specifies the SDP to be passed when recording is stopped. Currently unused.

Enable XferDPlan

Boolean, Defaults to 1

When enabled, the phone, while in the transfer state, will execute off-hook dialing plan rules. Defaults to 1.

Enable FwdDPlan

Boolean, Defaults to 0

When enabled, the phone, while in the forward state, will execute off-hook dialing plan rules. Defaults to 0.

Enable Pre DPlan

Boolean, Defaults to 0

When enabled, the phone, while in the on-hook state, will execute off-hook dialing plan rules. Defaults to 0.

IP Dial Prefix

String, Defaults to .

Sets a dialing prefix to be prepended before making IP dialed calls. Defaults to .

Enable DND

Integer, 0-2, Defaults to 0

When set to 0, enabling DND from the phone will have not affect from any line. When set to 1, enabling DND from the phone will have affect from any line. When set to 2, DND enabling/disabling will follow line rules.

DND Mode

Boolean, Defaults to 0

When enabled, the phone will use the DND settings as set for the line. When disabled, the phone will use the DND settings as set for the phone. Defaults to 0.

Enable Space DND

Boolean, Defaults to 0

When enabled, the phone will following DND timer as set by DNDStartTime and DNDEndTime

DND Start Time

Time, in 24-hour format, no separator

Sets the beginning time for DND to be auto-enabled.

DND End Time

Time, in 24-hour format, no separator

Sets the ending time for DND to be auto-disabled.

Enable White List

Boolean, Defaults to 1

When enabled, the phone will always allow calls from white listed Caller ID numbers. If disabled, the phone will ignore whitelisted numbers and allow other calls. Defaults to 1.

Enable Black List

Boolean, Defaults to 1

When enabled, the phone will never allow calls from black listed Caller ID numbers. If disabled, the phone will allow calls from black listed numbers. Defaults to 1.

Enable CallBar

Boolean, Defaults to 1

If disabled, the phone will ignore numbers/prefixes listed in its Restricted Outgoing Calls table. Defaults to 1.

Mute Ringing

Boolean, Defaults to 0

If enabled, the phone will not play ringing tone for incoming calls, instead only showing visual indicators. Defaults to 0.

Ban Dial Out

Boolean, Defaults to 0

If enabled, the phone will not allow any outgoing calls to be made. Defaults to 0.

Ban Empty CID

Boolean, Defaults to 0

If enabled, the phone will not allow any incoming calls that are void of Caller ID information. Defaults to 0.

Accept Any Call

Boolean, Defaults to 1

If disabled, the phone will not allow anonymous incoming calls. Defaults to 1.

Enable CLIP

Boolean, Defaults to 1

If disabled, the phone will not display incoming Caller ID information. Defaults to 1.

CallWaiting

Boolean, Defaults to 1

If disabled, the phone will not allow additional incoming calls if it is already on a call. Defaults to 1.

CallTransfer

Boolean, Defaults to 1

If disabled, the phone will not allow the user to transfer calls. Defaults to 1.

CallSemiXfer

Boolean, Defaults to 1

If disabled, the phone will not allow Semi / Blond transfers. Defaults to 1.

CallConference

Boolean, Defaults to 1

If disabled, the phone will not allow local conference calls. Defaults to 1.

Auto PickupNext

Boolean, Defaults to 0

If enabled, ending one call while another is ringing or in progress automatically picks up the ringing or other in-progress call. Defaults to 0.

Busy No Line

Boolean, Defaults to 0

If enabled, the phone will play dialing tone when off-hook, only if off-hook on a registered SIP line. Defaults to 0.

Auto Onhook

Boolean, Defaults to 1

If disabled, and the AutoOnhookTime has not been reached, the phone will remain off-hook after the conclusion of a handsfree call. Defaults to 1.

Auto Onhook Time

Integer, in seconds, Defaults to 3

Sets the time at which the phone should remain off-hook before going on-hook if AutoOnHook is not disabled. Defaults to 3.

Enable Intercom

Boolean, Defaults to 1

If disabled, the phone will not go into Intercom mode when receiving an INVITE that should cause it to auto-answer, e.g. Alert-Info: info=alert-autoanswer; or Call-Info: answer-after=2. Defaults to 1.

Intercom Mute

Boolean, Defaults to 0

If enabled, the phone, when it goes into Intercom mode, will automatically mute the microphone. Defaults to 0.

Intercom Tone

Boolean, Defaults to 0

If enabled, before the phone enters into an Intercom call, it will playback a tone. Defaults to 0.

Intercom Barge

Boolean, Defaults to 0

If enabled, the phone will allow an Intercom call to barge over an already-in-progress call. Defaults to 0.

Use Auto Redial

Boolean, Defaults to 0

If enabled, when the user calls a busy number, the phone will offer a pop-up to continue dialing the destination according to AutoRedialDelay and AutoRedialTimes. Defaults to 0.

Redial EnterCallLog

Integer, 0-1, Defaults to 0

If set to 0, the redial button will dial the last number dialed.  If set to 1, the phone will enter the call log and display recently dialed numbers.  Defaults to 1.

AutoRedial Delay

Integer, in seconds, Defaults to 30

Sets the delay, in seconds, the phone should make between AutoRedialTimes if UseAutoRedial is enabled and has been called by the user. Defaults to 30.

AutoRedial Times

Integer, Defaults to 5

Sets the number of times the phone should attempt to automatically redial a busy number. Defaults to 5.

Call Complete

Boolean, Defaults to 0

If enabled, the phone will, upon transitioning from having called a Busy party back to the idle state, provide a pop-up allowing the user to dial the busy party again, or cancel. Defaults to 0.

CHolding Tone

Boolean, Defaults to 1

If disabled, the phone will not play a tone every 40 seconds a call is left on hold. Defaults to 1.

CWaiting Tone

Boolean, Defaults to 1

If disabled, the phone will not play a tone when an incoming call arrives while another call is already in progress. Defaults to 1.

Hide DTMF Type

Integer, 0-3, Defaults to 0

Sets the type of DTMF hiding on the onscreen display:

Display all input - 0
Hide all input using a * character - 1
As digits are entered, change them to a * character after a small delay - 2
Display only the last digit properly, but other digits as a * character - 3

Talk DTMF Tone

Boolean, Defaults to 1

If disabled, local DTMF playback of tones will not be heard while the phone is on a call. Defaults to 1.

Dial DTMF Tone

Boolean, Defaults to 1

If disabled, local DTMF playback of tones will not be heard while the phone is dialing. Defaults to 1.

Psw Dial Mode

Boolean, Defaults to 0

If enabled, the phone will disguise, on-screen, dialed DTMF using * characters. Defaults to 0.

Psw Dial Length

Integer, Defaults to 0

Sets the number of digits that should be disguised if PswDialMode is enabled. Digits entered after PswDialLength is reached in length will not be disguised. Defaults to 0.

Psw Dial Prefix

String

Sets a dialing prefix that, if dialed, and if PswDialMode is enabled, will disguise, on-screen, dialed DTMF using * characters.

Enable MultiLine

Boolean, Defaults to 1

If enabled, the phone will allow up to 10 incoming calls. If disabled, the phone will only allow up to 2 incoming calls. Defaults to 1.

Allow IP Call

Boolean, Defaults to 1

If disabled, the phone will not be able to perform direct IP dialing. Defaults to 1.

Caller Name Type

Integer, Defaults to 0

Sets the priority of the caller name presentation:

Local Contact name, followed by Network Contact name, followed by SIP Display name - 0
Local Contact name, followed by SIP Display name, followed by Network Contact name - 1
Network Contact name, followed by Local Contact name, followed by SIP Display name - 2
Network Contact name, followed by SIP Display name, followed by Local Contact name - 3
SIP Display name, followed by Local Contact name, followed by Network Contact name - 4
SIP Display name, followed by Network Contact name, followed by Local Contact name - 5 

Mute For Ring

Boolean, Defaults to 0

If the phone is in Silent Mode, enabling this option will cause the phone to ring when calls are received. Defaults to 0

Auto Handle Video

Integer, 0-2, Defaults to 1

If set to 0, video must manually be enabled for incoming calls. If set to 1, video will be enabled for incoming calls. If set to 2, video calls will be rejected. Defaults to 1.

Default Ans Mode

Integer, 1-2. Defaults to 2.

If set to 1, answer only with audio. If set to 2, answer with audio and video. Defaults to 2.

Default Dial Mode

Integer, 1-2, Defaults to 1.

If set to 1, initiate calls only with audio. If set to 2, initiate calls with audio and video. Defaults to 1.

Hold To Transfer

Boolean, Defaults to 0

If enabled, the hold key can be used to accomplish a transfer. Defaults to 0.

Enable PreDial

Boolean, Defaults to 1

If disabled, the phone will go off-hook as soon as DTMF is entered, and off-hook dialing rules will be active. Defaults to 1.

Default Ext Line

Integer, 1-6, Defaults to 1

Sets the line which the phone will, by default, use for outbound calling. Defaults to 1.

Enable De fLine

Boolean, Defaults to 0

If enabled, show, while the phone is idle, in the phone's greeting / status bar, the default line that will be used. Defaults to 0.

Enable SelLine

Boolean, Defaults to 1

If disabled, do not automatically switch from an unregistered default line to a registered other line for outgoing calls. Defaults to 1.

Ring in Headset

Boolean, Defaults to 0

If enabled, play ringing tone out the headset port instead of the loudspeaker. Defaults to 0.

Auto Headset

Boolean, Defaults to 0

If enabled, answered calls will answer to the headset, not to the handset (unless lifted) or loudspeaker. Defaults to 0.

DND Return Code

String, Defaults to 480

Sets the SIP response code sent when the phone receives calls while DND is enabled. Defaults to 480.

Busy Return Code

String, Defaults to 486

Sets the SIP response code sent when the phone receives a call while Busy. Defaults to 486.

Reject Return Code

String, Defaults to 603

Sets the SIP response code when the phone rejects an incoming call. Defaults to 603.

Contact Type

Integer, 0-3, Defaults to 0

If set to 0, the contact is left alone. If set to 1, the contact may be used for DND, FWD, or white list. If set to 2, the contact is used for DND or white list. If set to 3, the contact is used for FWD or white list. Defaults to 0.

Enable Country Code

Boolean, Default to 0

If enabled, the phone will automatically truncate incoming numbers using the country code as defined by CountryCode and CallAreaCode and CodePlanList. Defaults to 0.

Country Code

String

Sets the country code to be truncated from incoming numbers.

Cal lArea Code

String

Sets the area code to be truncated from incoming numbers.

Number Privacy

Boolean, Defaults to 0

If enabled, followed the defined PrivacyRule in order to disguise digits. Defaults to 0.

Privacy Rule

String

Sets the privacy rule to apply to Number_Privacy number disguising where:

X defines the first number disguised

• defines a number to be disguised

. defines the last number to be disguised 

Trans DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a transfer is executed, in order to affect server-side transfer logic.

Hold DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a hold is executed, in order to affect server-side hold logic.

Conf DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a conference is executed, in order to affect server-side conference logic.

Disable Dial Search

Boolean, Defaults to 0

Currently Unused

Dial by Pound

Boolean, Defaults to 1

If disabled, the phone will not allow the use of the # key to send a call upon completion of dialing. The sent number does not include the # DTMF. Defaults to 1.

BTransfer by Pound

Boolean, Defaults to 0

If enabled, the phone will allow the use of the # key to blind transfer a call. Defaults to 0.

Onhook to BXfer

Boolean, Defaults to 0

If enabled, the phone will allow the completion of a blind transfer by a cradling of the handset. Defaults to 0.

Onhook to AXfer

Boolean, Defaults to 0

If enabled, the phone will allow the completion of an attended transfer by a cradling of the handset. Defaults to 0.

Conf Onhook to Xfer

Boolean, Defaults to 0

If enabled, the phone will allow the completion of a conference transfer by a cradling of the handset. Defaults to 0.

Dial Fixed Length

Boolean, Defaults to 0

If enabled, the phone will immediately dial the number that has been input according to a match of FixedLengthNums. Defaults to 0.

Fixed Length Nums

Integer

Sets a number of digits that once entered, if DialFixedLength is enabled, will be immediately dialed.

Dial by Timeout

Boolean, Defaults to 1

If disabled, the phone will not initiate a dial once the timeout set by DialTimeoutvalue is reached. Defaults to 1.

Dial Timeout value

Integer, in seconds, Defaults to 10

Sets the amount of time, in seconds, the phone will wait for additional digits before completing a dial.

Enable E OneSixFour

Boolean, Defaults to 0

If enabled, the phone will allow E.164 compliant dialing. Defaults to 0.

Text

String

Sets the Alert-Info string to be matched for this alert.

Ring Type

Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
Type 8
Type 9 

Sets the ringing tone type to apply to this alert.

Menu Password

Integer, Defaults to 789

Sets the password used to access the phone's password-protected advanced menu setting. Defaults to 789.

KeyLock Password

Integer, Defaults to 123

Sets the password used to unlock the phone when key lock has been engaged

Fast Keylock Code

Integer

Sets a key sequence that, when entered, immediately locks the phone.

Enable KeyLock

Boolean, Defaults to 0

If enabled, allows locking of the phone. Defaults to 0.

KeyLock Timeout

Integer in seconds

Specifies the timeout in seconds for keylock.

KeyLock Status

Boolean, Defaults to 0

Currently Unused

Emergency Call

String

Sets a number the phone is allowed to call, even while locked.

Push XML IP

IPv4 Hostname or address

Sets the IPv4 Hostname or address of an XML PUSH server that will transmit XML to the phone.

SIP Number Plan

Boolean, Defaults to 0

If enabled, non-numeric characters may be used when dialing out. Defaults to 0.

LDAP Search

Integer, 0-3, Defaults to 0

Sets the LDAP server against which to search. Defaults to 0. Obsolete.

Search Path

String

Sets the LDAP search path against which to search. Obsolete.

Caller Display T

Integer, 0-4, Defaults to 0

Sets the type of Caller Display to present to the user from:

Display Name Priority - 0
Display Number Only - 1
Alternate Display - 2
Scrolling Display - 3
Display Blank - 4 

CallLog DisplayType

Integer, Defaults to 0

If set to 1, display only numbers in the call log list. If set to 0, display names. Defaults to 0.

Enable Recv SMS

Boolean, Defaults to 1

If disabled, the phone will not be able to receive incoming text messages. Defaults to 1.

Enable Call History

Boolean, Defaults to 1

If disabled, the phone will not record call log entries.

Line Display Format

$protocol$instance
$name@$protocol$instance
$protocol$instance:$name 

Sets the default line label display format for SIP lines.

SIPn - $protocol$instance
xxx@SIPn - $name@$protocol$instance
SIPn:xxx - $protocol$instance:$name 

Enable MWI Tone

Boolean, Defaults to 0

If disabled, the phone will not play back a tone when receiving a new message and activating MWI. Defaults to 0.

LCD Title

Boolean, Defaults to Asterisk

Sets the text displayed in the idle screen status bar. Defaults to Asterisk

LCD Constrast

Integer, 1-10, Defaults to 5

Sets the display's contrast level. Obsolete.

Enable Energysaving

Integer, 0-32, Defaults to 4

Sets the display's brightness level when the BacklightOffTime is reached. If set to 0, display will never dim. Defaults to 4.

LCD Luminance Level

Integer, Defaults to 12

Sets the display's luminance level. Defaults to 12.

Backlight Off Time

Integer, 0-3600 in seconds, Defaults to 45

Sets the time, in seconds, at which the backlight will be dimmed to the level set by EnableEnergysaving. Defaults to 45.

Disable CHN IME

Boolean, Defaults to 0

If enabled, prevents Chinese input method. Defaults to 0.

Phone Model

String, Defaults to A30

Sets the phone model. Defaults to A30.

Host Name

String

Sets the phone host name.

Default Language

en, cn, tc, ru, it, de, fr, he

Sets the phone's default language as:

Chinese - cn
English - en
Chinese, Traditional - tc
French - fr
German - de
Hebrew - he
Italian - it
Russian - ru 

Defaults to en.

Enable Greetings

Boolean, Defaults to 0

If enabled, the phone will display greeting words. Defaults to 0.

Power

Boolean , Defaults to 0

If enabled, the LED will be set to on when the phone is powered on and idle.

MWI Or SMS

Integer, 0-3, Defaults to 3

Sets the behavior of the LED when MWI is received or a SIP Message is received as follows:

Off - 0
On - 1
Fast blink - 2
Slow blink - 3 

Defaults to 3

In Using

Boolean, Defaults to 0

If enabled, the LED will be turned on when the phone is off-hook or otherwise in use.

Ring

Integer, 0-3, Defaults to 2

Sets the behavior of the LED when the phone is ringing as follows:

Off - 0
On - 1
Fast blink - 2
Slow blink - 3

Defaults to 2 

Hold

Integer, 0-3, Defaults to 0

Sets the behavior of the LED when the phone has a call on hold as follows:

Off - 0
On - 1
Fast blink - 2
Slow blink - 3

Defaults to 0

Mute

Integer, 0-3, Defaults to 0

Sets the behavior of the LED when the phone is on mute as follows:

Off - 0
On - 1
Fast blink - 2
Slow blink - 3

Defaults to 0

Missed Call

Integer, 0-3, Defaults to 3

Sets the behavior of the LED when the phone has a missed call as follows:

Off - 0
On - 1
Fast blink - 2
Slow blink - 3

Defaults to 3

Handset Vol

Integer, 1-9, Defaults to 5

Sets the volume of the handset, Defaults to 5.

Handset Mic Vol

Integer, 1-9, Defaults to 3

Sets the gain of the handset microphone. Defaults to 3.

Headset Vol

Integer, 1-9, Defaults to 5

Sets the volume of the headset. Defaults to 5.

Headset Mic Vol

Integer, 1-9, Defaults to 3

Sets the gain of the headset microphone. Defaults to 3.

Headset Ring Vol

Integer, 1-9, Defaults to 5

Sets the volume of the headset ringing tone. Defaults to 5.

HandFree Vol

Integer, 1-9, Defaults to 5

Sets the volume of the handsfree loudspeaker. Defaults to 5.

HandFree Mic Vol

Integer, 1-9, Defaults to 3

Sets the gain of the handsfree microphone. Defaults to 3.

HandFree Ring Vol

Integer, 1-9, Defaults to 5

Sets the volume of the handsfree loudspeaker ringing tone. Defaults to 5.

Ring Type

Type 1
Type 2
Type 3
Type 4
Type 5
Type 6
Type 7
Type 8
Type 9

Sets the ringing type to apply to the phone by default.

Enable SNTP

Boolean, Defaults to 1

If disabled, the phone will not attempt to synchronize its clock to the defined SNTPServer

SNTP Server

IPv4 Hostname, Address, Defaults to 0.digium.pool.ntp.org

Sets the phone's primary SNTP server. Defaults to 0.digium.pool.ntp.org

Second SNTP Server

IPv4 Hostname, Address, Defaults to 1.digium.pool.ntp.org

Sets the phone's secondary SNTP server. Defaults to 1.digium.pool.ntp.org

Time Zone

-44, -40, -38, -36, -32, -28, -24, -30, -18, -16, -14, -12, -10, -8, -4, 0, 4, 8, 12, 14, 16, 18, 20, 22, 23, 24, 26, 28, 32, 35, 36, 38, 40, 42, 44, 46, 48, 51, 52, 54, 56, Defaults to -32

Sets the time zone for the phone as follows:

(UTC-11) Samoa, -44
(UTC-10) Hawaii-Aleutian,Alaska-Aleutia, -40
(UTC-9:30) French Polynesia, -38
(UTC-9) Alaska Time, -36
(UTC-8) Vancouver,Whitehorse,Tijuana,Mexicali,Pacific Time, -32
(UTC-7) Edmonton,Calgary,Mazatlan,Chihuahua,Mountain Time,United States-MST, -28
(UTC-6) Manitoba,Easter Islands,Mexico City,Acapulco,Central Time, -24
(UTC-5) Nassau,Montreal,Ottawa,Quebec,Havana,Eastern Time, -20
(UTC-4:30) Caracas, -18
(UTC-4) Halifax,Saint John,Santiago,Asuncion,Bermuda,Falkland Islands,Trinidad Tobago, -16
(UTC-3:30) New Foundland, -14
(UTC-3) Nuuk,Buenos Aires,no DST,DST, -12
(UTC-2:30) Newfoundland and Labrador, -10
(UTC-2) no DST, -8
(UTC-1) Azores, -1
(UTC) GMT,Greenland,Torshavn,Dublin,Lisboa,Porto,Funchal,Las Palmas,London,Morocco, 0
(UTC+1) Tirane,Vienna,Brussels,Caicos,Chad,Madrid,Zagreb,Prague,Kopenhagen,Paris,Berlin,Budapest,Rome,Luxembourg,Skopje,Amsterdam,Windhoek, 4
(UTC+2) Tallinn,Helsinki,Gaza,Athens,Tel Aviv,Amman,Riga,Beirut,Kishinev,Kaliningrad,Bucharest,Damascus,Kyiv,Odessa, 8
(UTC+3) East Africa Time,Baghdad,Moscow,Ankara, 12
(UTC+3:30) Teheran, 14
(UTC+4) Yerevan,Baku,Tbilisi,Aktau,Samara, 16
(UTC+4:30) Kabul, 18
(UTC+5) Aqtobe,Bishkek,Islamabad,Chelyabinsk, 20
(UTC+5:30) Calcutta, 22
(UTC+5:45) Katmandu, 23
(UTC+6) Astana,Almaty,Novosibirsk,Omsk, 24
(UTC+6:30) Naypyitaw, 26
(UTC+7) Krasnoyarsk,Bangkok, 28
(UTC+8) Beijing,Singapore,Perth,Irkutsk, Ulan-Ude, 32
(UTC+8:45) Eucla, 35
(UTC+9) Seoul,Tokyo,Yakutsk, Chita, 36
(UTC+9:30) Adelaide,Darwin, 38
(UTC+10) Sydney,Melbourne,Canberra,Brisbane,Hobart,Vladivostok, 40
(UTC+10:30) Lord Howe Islands, 42
(UTC+11) Noumea,Srednekolymsk Time, 44
(UTC+11:30) Norfolk Island, 46
(UTC+12) Wellington,Auckland,Kamchatka Time, 48
(UTC+12:45) Chatham Islands, 51
(UTC+13) Nukualofa, 52
(UTC+13:30) Chatham Islands, 54
(UTC+14) Kiribati, 56

Defaults to -32.

Time Zone Name

String, Defaults to UTC-8

Sets the name of the time zone in UTC format. Defaults to UTC-8

SNTP Timeout

Integer, in seconds, Defaults to 5000

Sets the time period at which the phone should re-sync its clock to the configured SNTP server. Defaults to 5000

DST Type

Integer, 0-2, Defaults to 1

If set to 0, the phone will not attempt to automatically set daylight savings times. If set to 1, the phone will attempt to automatically set daylight savings times. If set to 2, the phone utilizes manually configured logic to know when to set daylight savings time modes.

DST Location

Integer, 0-4, Defaults to 3

Sets the daylight savings time location for automatic setting as follows:

None - 0
China (Beijing) - 1
Singapore (Singapore) - 2
Australia (Perth) - 3
Russia (Irkutsk, Ulan-Ude) - 4 

Defaults to 3.

DST Rule Mode

Integer, 0-2, Defaults to 0

Sets the type of DST rule to employ as follows:

Disabled - 0
By Date - 1
By Week - 2 

Defaults to 0

DST Min Offset

Integer, in minutes, Defaults to 60

Sets the number of minutes to offset when the DST rule is in effect. Defaults to 60.

DST Start Mon

Integer, 1-12, Defaults to 3

Sets the month, by calendar, beginning in January, at which the DST rule should start. Defaults to 3

DST Start Week

-1, 1, 2, 3, 4, 5, 6, Defaults to 5

Sets the week, where -1 is the last week, at which the DST rule should start. Defaults to 5.

DST Start Wday

Integer, 0-6, Defaults to 0

Sets the week day, where Sunday is 0, at which the DST rule should start. Defaults to 0

DST Start Hour

Integer, 0-23, Defaults to 2

Sets the hour at which the DST rule should start. Defaults to 2

DST End Mon

Integer, 1-12, Defaults to 10

Sets the month, by calendar, beginning in January, at which the DST rule should end. Defaults to 10

DST End Week

-1, 1, 2, 3, 4, 5, 6, Defaults to 5

Sets the week, where -1 is the last week, at which the DST rule should end. Defaults to 5.

DST End Wday

Integer, 0-6, Defaults to 0

Sets the week day, where Sunday is 0, at which the DST rule should end. Defaults to 0.

DST End Hour

Integer, 0-23, Defaults to 2

Sets the hour at which the DST rule should end. Defaults to 2.

Enable TimeDisplay

n/a

Currently unused

Time Display Style

Integer, 0-1, Defaults to 1

If set to 0, display time using 24-hour format. If set to 1, display time using 12-hour format. Defaults to 1.

Date Display Style

Integer, 0-13, Defaults to 0

Sets the date display formatting that should be used by the phone as follows:

1 JAN MON - 0
JAN 1 MON - 1
MON 1 JAN - 2
MON JAN 1 - 3
DD MM YY - 4
DD MM YYYY - 5
MM DD YY - 6
MM DD YYYY - 7
YY MM DD - 8
YYYY MM DD - 9
1 January Monday - 10
January 1 Monday - 11
Monday 1 January - 12
Monday January 1 - 13 

Date Separator

Integer, 0-3, Defaults to 0

Sets the date display separator that should be used by the phone as follows:

/, 0
-, 1
., 2
(space character), 3 

Screen Saver Type

n/a

Currently unused

Screen Timeout

n/a

Currently unused

Enable ActivePeriod

n/a

Currently unused

Period One Start

n/a

Currently unused

Period One End Time

n/a

Currently unused

Period Two Start

n/a

Currently unused

Period Two End Time

n/a

Currently unused

Screen Saver App

n/a

Currently unused

Sleep After Active

n/a

Currently unused

Sleep Timeout

n/a

Currently unused

Desktop Softkey

Defaults to: history;contact;dnd;menu;

Sets the soft key mapping for the idle screen.

Talking Softkey

Defaults to: hold;xfer;conf;end;

Sets the soft key mapping for the on-call screen.

Ringing Softkey

Defaults to: accept;none;forward;reject;

Sets the soft key mapping for the ringing (incoming call) screen.

Alerting Softkey

Defaults to: end;none;none;none;

Sets the soft key mapping for the alerting screen.

XAlerting Softkey

Defaults to: end;none;none;none;

Sets the soft key mapping for the transfer alerting screen.

Conference Softkey

Defaults to: hold;none;split;end;

Sets the soft key mapping for the conference screen.

Waiting Softkey

Defaults to: hold;xfer;conf;end;

Sets the soft key mapping for the waiting screen.

Ending Softkey

Defaults to: repeat;none;none;end;

Sets the soft key mapping for the ending (far-end has disconnected) screen.

DialerPre Softkey

Defaults to: delete;none;send;exit;

Sets the soft key mapping for the on-hook dialing screen.

DialerXfer Softkey

Defaults to: delete;xfer;send;exit;

Sets the soft key mapping for the transfer screen.

DialerCfwd Softkey

Defaults to: delete;none;cfwd;exit;

Sets the soft key mapping for the call forwarding screen.

Desktop Click

Defaults to: history;status;paccout;naccout;menu;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the Idle state.

Dailer Click

Defaults to: pline;nline;none;none;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the Dialing state.

Call Click

Defaults to: pcall;ncall;voldown;volup;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the on-call state.

Desktop Long Press

Defaults to: status;none;none;mwi;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) when they are long-pressed.

Softkey Mode

Integer, 0-2, Defaults to 1

If set to 0, custom soft keys are disabled. If set to 1, the More softkey is enabled for keys exceeding four. If set etc 2, the Arrow soft key is used for keys exceeding four. Currently hard-coded to 1.

DialerConf Softkey

Defaults to: contact;clogs;redial;video;cancel;

Currently unused.

Agent Username

String

Sets the agent username.

Agent Password

String

Sets the agent password.

Agent Number

String

Sets the agent number.

Agent Sipline

Integer, 0-6, Defaults to 0

Sets the SIP line to use for Agent login.

Agent Status

Integer, 0-4, Defaults to 0

Sets the agent status as follows:

LOGON - 0
LOGOFF - 1
UNAVILABLE - 2
AVAILABLE - 3
WRAPUP - 4 

Agent Status Reason

String

Sets the agent's status reason code.

Title

String

Sets the displayed title of the remote Broadsoft phonebook.

URL

String

Sets the URL of the remote Broadsoft phonebook.

Username

String

Sets the username used to retrieve the remote Broadsoft phonebook.

Password

String

Sets the password used to retrieve the remote Broadsoft phonebook.

SipLine

Integer, 0-5, Defaults to 0

Sets the SIP line with which to associate the remote Broadsoft phonebook.

Title

String

Sets the displayed title of the remote Broadsoft call log.

URL

String

Sets the URL of the remote Broadsoft call log.

Username

String

Sets the username used to retrieve the remote Broadsoft call log.

Password

String

Sets the password used to retrieve the remote Broadsoft call log.

SipLine

Integer, 0-5, Defaults to 0

Sets the SIP line with which to associate the remote Broadsoft call log.

Title

String

Sets the displayed title of the LDAP phonebook.

Server

String

Sets the IPv4 address or hostname of the LDAP server.

Port

Integer, Defaults to 389

Sets the port for contacting the LDAP server. Defaults to 389.

Base

String, limited to 39 characters

Sets the LDAP search root / base for queries.

Use SSL

Boolean, Defaults to 0

If enabled, the phone will attempt to use SSL to connect to the LDAP server. Defaults to 0.

Version

Integer, 2-3, Defaults to 3

Sets the LDAP protocol version to use when communication to the server. Defaults to 3.

Calling Line

Integer, -1-6, Defaults to -1

If -1, creating calls through the LDAP phonebook will be done via the current line. If the value is 1-6, use the corresponding SIP line to place the calls. Defaults to -1.

Bind Line

Integer, -1-6, Defaults to 01

If -1, queries through the LDAP phonebook will be done via the current line. If the value is 16, use the corresponding SIP line to place the calls. Defaults to -1.

In Call Search

Boolean, Defaults to 0

If enabled, the phone will attempt to search the LDAP phonebook for matches for incoming calls.

Out Call Search

Boolean, Defaults to 0

If enabled, the phone will attempt to search the LDAP phonebook for matching for outgoing calls.

Anonymous

Boolean, Defaults to 0

Unused.

Authenticate

Integer, 0-3, Defaults to 3

Specifies the method of authentication to be used against the LDAP server as follows:

None - 0
Digest-MD5 - 1
CRAM-MD5 - 2
Simple - 3 

Username

String

Sets the LDAP server authentication username.

Password

String

Sets the LDAP server authentication password.

Tel Attr

String, defaults to telephoneNumber

Sets the LDAP attribute name to search for telephone numbers.

Mobile Attr

String, defaults to mobile

Sets the LDAP attribute name to search for mobile numbers.

Other Attr

String

Sets an additional LDAP attribute name that can be searched for other numbers.

Name Attr

String, defaults to "cn sn ou"

Sets the LDAP name attributes that should be searched for people's names.

Sort Attr

An attribute defined by NameAttr

Sets the attribute, as defined by NameAttr, that should be sorted.

Displayname

An attribute defined by NameAttr

Sets the attribute, as defined by NameAttr, that should be displayed on the phone.

Number Filter

String, Defaults to (|(telephoneNumber=%)(mobile=%)(other=%))

Sets the LDAP search results filter for number filtering. Defaults to (|(telephoneNumber=%)(mobile=%)(other=%))

Name Filter

String, Defaults to (|(cn=%)(sn=%))

Sets the LDAP search results filter for name filtering. Defaults to (|(cn=%)(sn=%))

Max Hits

Integer, Defaults to 50

Sets the maximum number of results that the LDAP server will return for a given search. Defaults to 50.

Name

String

Sets the displayed name of the remote phonebook.

Addr

URL string

Sets the address of the remote phonebook.

UserName

String

Sets the username optionally used to retrieve the remote phonebook.

PassWd

String

Sets the password optionally used to retrieve the remote phonebook.

SipLine

Integer, -1-6, Defaults to -1

Sets the SIP line with which to associate the remote phonebook. If set to -1, use the current line. Otherwise, use the specified SIP line, from 1-6.

BindLine

Integer, -1-6, Defaults to -1

Sets the SIP line with which to bind the remote phonebook. If set to -1, use the current line. Otherwise, use the specified SIP line, from 1-6.

Onhook Time

Time in milliseconds, Defaults to 120

Sets the on-hook debounce timer. Defaults to 120.

Enabled Active Uri

Boolean, Defaults to 1

If disabled, the phone will not accept remote phone control from the server defined by ActiveUriIP. Defaults to 1.

Enabled Action Url

Boolean, Defaults to 1

If disabled, the phone will not process any of the Action URL Event settings. Defaults to 1.

Active Uri IP

String

Specifies the IP address of the remote server sending commands to the phone.

Start Reboot Url

String

Specifies the URL the phone should contact when it beings the reboot process.

Boot Completed Url

String

Specifies the URL the phone should contact when it completes the boot process.

IP Change Url

String

Specifies the URL the phone should contact when it changes IP addresses.

Reg On Url

String

Specifies the URL the phone should contact when it completes a SIP registration.

Reg Off Url

String

Specifies the URL the phone should contact when SIP registration is disabled.

Reg Failed Url

String

Specifies the URL the phone should contact when SIP registration fails.

PhoneState Idle Url

String

Specifies the URL the phone should contact when the phone returns from in-use to idle state.

PhoneState Talking

String

Specifies the URL the phone should contact when it transitions from idle to talking (in-use).

PhoneState Ringing

String

Specifies the URL the phone should contact when it transitions to the ringing state.

DND On Url

String

Specifies the URL the phone should contact when DND is enabled.

DND Off Url

String

Specifies the URL the phone should contact when DND is disabled.

Always FWD On Url

String

Specifies the URL the phone should contact when Call Forward Always is enabled.

Always FWD Off Url

String

Specifies the URL the phone should contact when Call Forward Always is disabled.

Busy FWD On Url

String

Specifies the URL the phone should contact when Call Forward Busy is enabled.

Busy FWD Off Url

String

Specifies the URL the phone should contact when Call Forward Busy is disabled.

No Ans FWD On Url

String

Specifies the URL the phone should contact when Call Forward No Answer is enabled.

No Ans FWD Of fUrl

String

Specifies the URL the phone should contact when Call Forward No Answer is disabled.

Mute On Url

String

Specifies the URL the phone should contact when Mute is enabled.

Mute Off Url

String

Specifies the URL the phone should contact when Mute is disabled.

Incmoing Call Url

String

Specifies the URL the phone should contact when it receives an incoming call.

Outgoing Call Url

String

Specifies the URL the phone should contact when it makes an outgoing call.

Call Active Url

String

Specifies the URL the phone should contact when a call active.

Call Stop Url

String

Specifies the URL the phone should contact when a call is stopped.

Transfer Url

String

Specifies the URL the phone should contact when a call is transferred.

Hold On Url

String

Specifies the URL the phone should contact when it places a call on hold.

Hold Off Url

String

Specifies the URL the phone should contact when it takes a call off of hold.

Held On Url

String

Specifies the URL the phone should contact when it is placed on hold.

Held Off Url

String

Specifies the URL the phone should contact when it is taken off of hold.

Mute On Call Url

String

Specifies the URL the phone should contact when muting a call.

Mute Off Call Url

String

Specifies the URL the phone should contact when unmuting a call.

New Missed call Url

String

Specifies the URL the phone should contact when it receives a new missed call.

New MWI Url

String

Specifies the URL the phone should contact when it receives a new MWI event.

New SMS Url

String

Specifies the URL the phone should contact when it receives a new MESSAGE event.

At Enabled

n/a

Used during manufacturing testing. Not user controllable.

At Server

n/a

Used during manufacture testing. Not user controllable.

Priority

Integer, 0-10, Defaults to 0

Sets the priority value at which normal calls should take precedence over multicasted audio calls. At 0, normal calls will take priority over any multicasted calls. At 1, normal calls are lower priority than multicast priority 1 calls, but higher priority than any other multicast priority levels. Additional values follow the same logic. Defaults to 0.

Enable Priority

Boolean, Defaults to 0

If enabled, the phone will sort multicast audio by priority, allowing one multicast audio stream to take precedence over another multicast audio stream. Defaults to 0.

Name

String

Sets the name to be displayed on the phone's screen when audio from this multicast listener is played back.

Host

IPv4 Multicast address

Sets the IPv4 multicast address for this listener.

Port

Integer

Sets the port for this multicast listener.

Web Server Type

Boolean, Defaults to 0

If enabled, the phone will permit access to its configuration web pages using HTTPs, instead of HTTP. Defaults to 0.

Web Port

Integer, Defaults to 80

Sets the port for HTTP access. Defaults to 80.

Https Web Port

Integer, Defaults to 443

Sets the port for HTTPs access. Defaults to 443.

Remote Control

Boolean, Defaults to 1

If disabled, the phone will not permit web configuration across the WAN port.

Enable MMI Filter

Boolean, Defaults to 0

If enabled the phone will not permit web configuration from any device not in the filter list.

Web Authentication

Boolean, Defaults to 0

If enabled, the phone utilizes basic auth instead of digest auth. Defaults to 0.

Enable Telnet

Boolean, Defaults to 0

If enabled, the phone will allow telnet access. Defaults to 0.

Telnet Port

Integer, Defaults to 23

Sets the port for Telnet access. Defaults to 23.

Telnet Prompt

String

Sets the prompt to be given after logging in via Telnet.

Logon Timeout

Time in minutes, Defaults to 15

Specifies the time before web logins are timed out. Defaults to 15.

Name

String

Sets the username for this account.

Password

String

Sets the password for this account.

Level

Integer: 5, 10

Sets the access level for this account. 5 for users, 10 for administrators.

TR069 Tone

Boolean, Defaults to 1

If disabled, the phone will not play a prompt tone after a successful TR069 connection. Defaults to 1.