A20, A22 and A25 TXT Configuration 2.3.3

Version

String

If the phone is configured for auto provisioning and it successfully loads this configuration, the version string will be displayed on-screen.

WAN Mode

DHCP, STATIC, PPPOE, Defaults to DHCP

Sets the method of network access for the phone. Defaults to DHCP.

WAN IP

IPv4 Address

Shows (DHCP / PPPOE) or sets (STATIC) the IPv4 address of the phone.

WAN Subnet Mask

IPv4 net mask

Shows (DHCP / PPPOE) or sets (STATIC) the IPv4 net mask of the phone.

WAN Gateway

IPv4 network gateway

Shows (DHCP / PPPOE) or sets (STATIC) the IPv4 network gateway of the phone.

Primary DNS

IPv4 Address

Shows (DHCP / PPPOE) or sets (STATIC) the primary DNS server of the phone.

Secondary DNS

IPv4 Address

Shows (DHCP / PPPOE) or sets (STATIC) the secondary DNS server of the phone.

Enable DHCP

Boolean, Defaults to 1

Enables or disables DHCP network configuration request. Defaults to 1.

Use Vendor Class ID

Boolean, Defaults to 0

Configures the phone to send DHCP Option 61, Vendor Class Identifier. Defaults to 0.

Vendor Class ID

String, Defaults to Asterisk

Sets the Vendor Class Identifier of the phone. Defaults to Asterisk.

DHCP Auto DNS

Boolean, Defaults to 1

Configures the phone to accept DNS servers provided by DHCP. If disabled, the phone will use the DNS servers defined by the PrimaryDNS and SecondaryDNS net configuration elements. Defaults to 1.

DHCP Auto Time

Boolean, Defaults to 1

Configures the phone to set its time and SNTP server based upon receipt of DHCP Option 42. If disabled, the phone will use the NTP server as defined by the SNTPServer date configuration element and time as defined in other date configuration elements. Defaults to 1.

DHCP Option 100-101

Boolean, Defaults to 1

If disabled, the phone will not set its clock according to time as provided by DHCP Options 100 and 101. Defaults to 1.

ARP Cache Life

Integer, in minutes, Defaults to 10

Specifies the lifetime, in minutes, of a cached ARP entry. Defaults to 10.

Enable PPPoE

Boolean, Defaults to 0

Configures the phone to perform PPPoE authentication in order to retrieve its network configuration. Defaults to 0

RTP Initial Port

Integer, Defaults to 10000

Sets the starting RTP port used for calls. Defaults to 10000

RTP Port Quantity

Integer, Defaults to 200

Sets the number of RTP ports to span across before recycling. Defaults to 200.

SNTP Server

IPv4 Hostname, Address, Defaults to 0.digium.pool.ntp.org

Sets the phone's primary SNTP server. Defaults to 0.digium.pool.ntp.org

Second SNTP Server

IPv4 Hostname, Address, Defaults to 1.digium.pool.ntp.org

Sets the phone's secondary SNTP server. Defaults to 1.digium.pool.ntp.org

Enable SNTP

Boolean, Defaults to 1

If disabled, the phone will not attempt to synchronize its clock to the defined SNTP Server

Time Zone

-44, -40, -38, -36, -32, -28, -24, -30, -18, -16, -14, -12, -10, -8, -4, 0, 4, 8, 12, 14, 16, 18, 20, 22, 23, 24, 26, 28, 32, 35, 36, 38, 40, 42, 44, 46, 48, 51, 52, 54, 56, Defaults to -32

Sets the time zone for the phone as follows:

(UTC-11) Samoa, -44
(UTC-10) Hawaii-Aleutian,Alaska-Aleutia, -40
(UTC-9:30) French Polynesia, -38
(UTC-9) Alaska Time, -36
(UTC-8) Vancouver,Whitehorse,Tijuana,Mexicali,Pacific Time, -32
(UTC-7) Edmonton,Calgary,Mazatlan,Chihuahua,Mountain Time,United States-MST, -28
(UTC-6) Manitoba,Easter Islands,Mexico City,Acapulco,Central Time, -24
(UTC-5) Nassau,Montreal,Ottawa,Quebec,Havana,Eastern Time, -20
(UTC-4:30) Caracas, -18
(UTC-4) Halifax,Saint John,Santiago,Asuncion,Bermuda,Falkland Islands,Trinidad Tobago, -16
(UTC-3:30) New Foundland, -14
(UTC-3) Nuuk,Buenos Aires,no DST,DST, -12
(UTC-2:30) Newfoundland and Labrador, -10
(UTC-2) no DST, -8
(UTC-1) Azores, -1
(UTC) GMT,Greenland,Torshavn,Dublin,Lisboa,Porto,Funchal,Las Palmas,London,Morocco, 0
(UTC+1) Tirane,Vienna,Brussels,Caicos,Chad,Madrid,Zagreb,Prague,Kopenhagen,Paris,Berlin,Budapest,Rome,Luxembourg,Skopje,Amsterdam,Windhoek, 4
(UTC+2) Tallinn,Helsinki,Gaza,Athens,Tel Aviv,Amman,Riga,Beirut,Kishinev,Kaliningrad,Bucharest,Damascus,Kyiv,Odessa, 8
(UTC+3) East Africa Time,Baghdad,Moscow,Ankara, 12
(UTC+3:30) Teheran, 14
(UTC+4) Yerevan,Baku,Tbilisi,Aktau,Samara, 16
(UTC+4:30) Kabul, 18
(UTC+5) Aqtobe,Bishkek,Islamabad,Chelyabinsk, 20
(UTC+5:30) Calcutta, 22
(UTC+5:45) Katmandu, 23
(UTC+6) Astana,Almaty,Novosibirsk,Omsk, 24
(UTC+6:30) Naypyitaw, 26
(UTC+7) Krasnoyarsk,Bangkok, 28
(UTC+8) Beijing,Singapore,Perth,Irkutsk, Ulan-Ude, 32
(UTC+8:45) Eucla, 35
(UTC+9) Seoul,Tokyo,Yakutsk, Chita, 36
(UTC+9:30) Adelaide,Darwin, 38
(UTC+10) Sydney,Melbourne,Canberra,Brisbane,Hobart,Vladivostok, 40
(UTC+10:30) Lord Howe Islands, 42
(UTC+11) Noumea,Srednekolymsk Time, 44
(UTC+11:30) Norfolk Island, 46
(UTC+12) Wellington,Auckland,Kamchatka Time, 48
(UTC+12:45) Chatham Islands, 51
(UTC+13) Nukualofa, 52
(UTC+13:30) Chatham Islands, 54
(UTC+14) Kiribati, 56

Defaults to -32.

Location

Integer, 0-4, Defaults to 3

Sets the daylight savings time location for automatic setting as follows:None - 0
China (Beijing) - 1
Singapore (Singapore) - 2
Australia (Perth) - 3
Russia (Irkutsk, Ulan-Ude) - 4 Defaults to 0.

Time Zone Name

String, Defaults to UTC-8

Sets the name of the time zone in UTC format. Defaults to UTC-8.

Enable DST

Boolean, Defaults to 1

If disabled, the phone will not adjust its clock for Daylight saving time rules. Defaults to 1.

DST Fixed Type

Integer, 0-2, Defaults to 2.

If set to 0, the phone will not attempt to automatically set daylight savings times. If set to 1, the phone will attempt to automatically set daylight savings times. If set to 2, the phone utilizes manually configured logic to know when to set daylight savings time modes.

SNTP Timeout

Integer, in seconds, Defaults to 5000

Sets the time period at which the phone should re-sync its clock to the configured SNTP server. Defaults to 5000.

DST Min Offset

Integer, in minutes, Defaults to 60

Sets the number of minutes to offset when the DST rule is in effect. Defaults to 60.

DST Start Mon

Integer, 1-12, Defaults to 3

Sets the month, by calendar, beginning in January, at which the DST rule should start. Defaults to 3.

DST Start Week

-1, 1, 2, 3, 4, 5, 6, Defaults to 5

Sets the week, where -1 is the last week, at which the DST rule should start. Defaults to 5.

DST Start Wday

Integer, 0-6, Defaults to 0

Sets the week day, where Sunday is 0, at which the DST rule should start. Defaults to 0.

DST Start Hour

Integer, 0-23, Defaults to 2

Sets the hour at which the DST rule should start. Defaults to 2.

DST End Mon

Integer, 1-12, Defaults to 10

Sets the month, by calendar, beginning in January, at which the DST rule should end. Defaults to 10.

DST End Week

-1, 1, 2, 3, 4, 5, 6, Defaults to 5

Sets the week, where -1 is the last week, at which the DST rule should end. Defaults to 5.

DST End Wday

Integer, 0-6, Defaults to 0

Sets the week day, where Sunday is 0, at which the DST rule should end. Defaults to 0.

DST End Hour

Integer, 0-23, Defaults to 2

Sets the hour at which the DST rule should end. Defaults to 2.

Language

0, en, cn, tc, nl, fr, ru, it, es, jp, bg, slo, cat, eus, de, es_l, pt, cz, gl, in, ma, hu, ar, uk, Defaults to 0 (English)

Sets the phone's default language as:

Arabic - ar
Bulgarian - bg
Catalan - cat
Chinese - cn
Chinese, Traditional - tc
Czech - cz
Dutch - nl
English - 0, en
Euskera - eus
French - fr
Gallego - gl
German - de
Hungarian - hu
Indonesian - in
Italian - it
Japanese - jp
Portuguese - pt
Russian - ru 
Slovenian - slo
Spanish - es
Latin American Spanish - es_l
Malaysian - ma
Ukranian - uk 

Defaults to 0, English (en).

Push XML IP

IPv4 Hostname or address

Sets the IPv4 Hostname or address of an XML PUSH server that will transmit XML to the phone.

Enable Call History

Boolean, Defaults to 1

If disabled, the phone will not record call log entries.

Active Uri IP

String

Specifies the IP address of the remote server sending commands to the phone.

Boot Completed Url

String

Specifies the URL the phone should contact when it completes the boot process.

Reg On Url

String

Specifies the URL the phone should contact when it completes a SIP registration.

Reg Off Url

String

Specifies the URL the phone should contact when SIP registration is disabled.

Reg Failed Url

String

Specifies the URL the phone should contact when SIP registration fails.

Offhook Url

String

Specifies the URL the phone should contact when the phone is taken off-hook.

Onhook Uri

String

Specifies the URI the phone should contact when the phone is placed on-hook.

Incmoing Call Url

String

Specifies the URL the phone should contact when it receives an incoming call.

Outgoing Call Url

String

Specifies the URL the phone should contact when it makes an outgoing call.

Call Active Url

String

Specifies the URL the phone should contact when an incoming call becomes an active call.

Call Stop Url

String

Specifies the URL the phone should contact when a call is ended.

DND On Url

String

Specifies the URL the phone should contact when DND is enabled.

DND Off Url

String

Specifies the URL the phone should contact when DND is disabled.

Always FWD On Url

String

Specifies the URL the phone should contact when Call Forward Always is enabled.

Always FWD Off Url

String

Specifies the URL the phone should contact when Call Forward Always is disabled.

Busy FWD On Url

String

Specifies the URL the phone should contact when Call Forward Busy is enabled.

Busy FWD Off Url

String

Specifies the URL the phone should contact when Call Forward Busy is disabled.

No Ans FWD On Url

String

Specifies the URL the phone should contact when Call Forward No Answer is enabled.

No Ans FWD Off Url

String

Specifies the URL the phone should contact when Call Forward No Answer is disabled.

Transfer Url

String

Specifies the URL the phone should contact when it transfers a call.

B Transfer Url

String

Specifies the URL the phone should contact when it performs a blind transfer.

A Transfer Url

String

Specifies the URL the phone should contact when it performs an attended transfer.

Hold Url

String

Specifies the URL the phone should contact when it places a call on hold.

Unhold Url

String

Specifies the URL the phone should contact when it takes a call off of hold.

Mute Url

String

Specifies the URL the phone should contact when Mute is enabled.

Unmute Url

String

Specifies the URL the phone should contact when Mute is disabled.

Missed call Url

String

Specifies the URL the phone should contact when it receives a new missed call.

IP Change Url

String

Specifies the URL the phone should contact when it changes IP addresses.

Idle to Busy Url

String

Specifies the URL the phone should contact when it transitions from the idle to the busy (in-use) state.

Busy to Idle Url

String

Specifies the URL the phone should contact when it transitions from the busy (in-use) to the idle state.

ATE ID

Unused

Unused

All Pswd Encryption

Boolean, Defaults to 0

If enabled, passwords contained in exported phone configurations will be disguised. Defaults to 0.

Dial by Pound

Boolean, Defaults to 1

If disabled, the phone will not allow the use of the # key to send a call upon completion of dialing. The sent number does not include the # DTMF. Defaults to 1.

BTransfer by Pound

Boolean, Defaults to 1

If enabled, the phone will allow the use of the # key to blind transfer a call. Defaults to 1.

Onhook to BXfer

Boolean, Defaults to 0

If enabled, the phone will allow the completion of a blind transfer by a cradling of the handset. Defaults to 0.

Onhook to AXfer

Boolean, Defaults to 1

If enabled, the phone will allow the completion of an attended transfer by a cradling of the handset. Defaults to 1.

Memory Key to BXfer

Boolean, Defaults to 0

If enabled, pressing a BLF after using the transfer hard key will affect a blind transfer. Defaults to 0.

Xfer On Conf Onhook

Boolean, Defaults to 0

If enabled, going on-hook can complete a conference transfer. Defaults to 0.

Dial Fixed Length

Boolean, Defaults to 0

If enabled, the phone will immediately dial the number that has been input according to a match of Fixed Length Nums. Defaults to 0.

Fixed Length Nums

Integer, Defaults to 11

Sets a number of digits that once entered, if Dial Fixed Length is enabled, will be immediately dialed. Defaults to 11.

Dial by Timeout

Boolean, Defaults to 1

If disabled, the phone will not initiate a dial once the timeout set by Dial Timeout value is reached. Defaults to 1.

Dial Timeout value

Integer, in seconds, Defaults to 5

Sets the amount of time, in seconds, the phone will wait for additional digits before completing a dial. Defaults to 5

Dialpeer With Line

0

Defaults to 0.

Accept Any Call

Boolean, Defaults to 1

If disabled, the phone will not allow anonymous incoming calls. Defaults to 1.

IP Dial Prefix

String, Defaults to .

Sets a dialing prefix to be prepended before making IP dialed calls. Defaults to .

Auto Switch Call

Boolean, Defaults to 0

If enabled, the phone will switch and provide ringing indication for new incoming calls if a multicast call was already in progress. Defaults to 0.

Transf SDial

DTMF

If defined, and if you have a speed dial set for this digit, the phone will, in the transfer state, use the speed dial assigned for this digit to affect the transfer.

Enable Code Plan

Boolean, Defaults to 0

If enabled, the phone will automatically truncate incoming numbers using the country code as defined by Country Code, Area Code and Code Plan List. Defaults to 0.

Country Code

String

Sets the country code to be truncated from incoming numbers.

Area Code

String

Sets the area code to be truncated from incoming numbers.

Transfer DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a transfer is executed, in order to affect server-side transfer logic.

Hold DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a hold is executed, in order to affect server-side hold logic.

Conf DTMF Code

DTMF string

If defined, sets digits that are sent to the server when a conference is executed, in order to affect server-side conference logic.

ID

P1

Sets the port to which the config applies; always set to P1.

Enable DND

Integer, 0-2, Defaults to 0

When set to 0, enabling DND from the phone will have not affect from any line. When set to 1, enabling DND from the phone will have affect from any line. When set to 2, DND enabling/disabling will follow line rules.

DND Mode

Integer, 0-1, Defaults to 0

Sets the DND mode for the phone. If set to 0, DND mode for the phone (Enable DND) will be used. If set to 1, DND will be obeyed per-line. Defaults to 0.

Call Record Type

Integer, 0-1, Defaults to 0

Sets the method of display within the Call Log. If set to 0, displays names. If set to 1, displays numbers. Defaults to 0.

Enable Force Rin

Boolean, Defaults to 0

If enabled, the mute and volume keys can prevent the phone from ringing audibly. If disabled, the mute and volume keys can be used to mute the ringing sound. Defaults to 0.

Mute Ringing

Boolean, Defaults to 0

If enabled, the phone will not ring audibly, only visually, on incoming calls. Defaults to 0.

CWaiting Tone

Boolean, Defaults to 1

If disabled, the phone will not play a call waiting tone when an incoming call arrives while another call is in progress. Defaults to 1.

Ban Dial Out

Boolean, Defaults to 0

If enabled, the phone will not be allowed to make outgoing calls, but can still receive incoming calls. If disabled, the phone can both make and receive calls. Defaults to 0.

Ban Empty CID

Boolean, Defaults to 0

If enabled, the phone will reject any calls that arrive without Caller ID. Defaults to 0.

Enable CLIP

Boolean, Defaults to 1

If disabled, the phone will not display calling party identification on-screen for incoming calls. Defaults to 1.

CallWaiting

Boolean, Defaults to 1

If disabled, the phone will reject additional incoming calls while one is already in progress. Defaults to 1.

CallTransfer

Boolean, Defaults to 1

If disabled, the phone will not be able to transfer calls. Defaults to 1.

CallSemiXfer

Boolean, Defaults to 1

If disabled, the phone will not be able to perform blond transfers. Defaults to 1.

CallConference

Boolean, Defaults to 1

If disabled, the phone will not be able to perform conference calls. Defaults to 1.

AutoAnswer

Boolean, Defaults to 0

If enabled, and if the No Answer Time has elapsed, the phone will automatically answer an incoming call. Defaults to 0.

No Answer Time

Integer, in seconds, Defaults to 20

Sets the amount of time, in seconds, the phone should wait on an incoming call before proceeding to AutoAnswer, if AutoAnswer is enabled. Defaults to 20.

Warm Line Time

Integer, in seconds, 0-9, Defaults to 0.

Sets the amount of time the phone must remain off-hook before attempting to execute Hotline functionality.

Hotline Num

String

Sets the number to be dialed when the off-hook time is greater than the Warm Line Time and Enable Hotline is enabled.

Auto PickupNext

Boolean, Defaults to 0

If enabled, ending one call while another is ringing or in progress automatically picks up the ringing or other in-progress call. Defaults to 0.

Busy No Line

Boolean, Defaults to 0

If enabled, the phone will play dialing tone when off-hook, only if off-hook on a registered SIP line. Defaults to 0.

Auto Onhook

Boolean, Defaults to 1

If disabled, and the Auto Onhook Time has not been reached, the phone will remain off-hook after the conclusion of a handsfree call. Defaults to 1.

Auto Onhook Time

Integer, in seconds, Defaults to 3

Sets the time at which the phone should remain off-hook before going on-hook if Auto Onhook is not disabled. Defaults to 3.

DND Code

Integer, 0-3, Defaults to 1

Sets the SIP response code provided when the phone has DND enabled as follows:

404 (Not Found) - 0
480 (Temporarily Not Available) - 1
486 (Busy Here) - 2
603 (Decline) - 3 

Defaults to 1

Busy Code

Integer, 0-3, Defaults to 2

Sets the SIP response code provided when the phone is busy as follows:

404 (Not Found) - 0
480 (Temporarily Not Available) - 1
486 (Busy Here) - 2
603 (Decline) - 3 

Defaults to 2

Reject Code

Integer, 0-3, Defaults to 3

Sets the SIP response code provided when the phone rejects a call as follows:

404 (Not Found) - 0
480 (Temporarily Not Available) - 1
486 (Busy Here) - 2
603 (Decline) - 3 

Defaults to 3

Caller Name Type

Integer, 0-5, Defaults to 0

Sets the priority of the caller name presentation:

Phonebook, followed by LDAP, followed by SIP Display name - 0
Phonebook, followed by SIP Display name, followed by LDAP - 1
LDAP, followed by Phonebook, followed by SIP Display name - 2
LDAP, followed by SIP Display name, followed by Phonebook - 3
SIP Display name, followed by Phonebook, followed by LDAP - 4
SIP Display name, followed by LDAP, followed by Phonebook - 5 

Enable Intercom

Boolean, Defaults to 1

If disabled, the phone will not go into Intercom mode when receiving an INVITE that should cause it to auto-answer, e.g. Alert-Info : info=alert-autoanswer; or Call-Info: answer-after=2. Defaults to 1.

Intercom Mute

Boolean, Defaults to 0

If enabled, the phone, when it goes into Intercom mode, will automatically mute the microphone. Defaults to 0.

Intercom Tone

Boolean, Defaults to 1

If disabled, the phone will not play back a tone before it begins an Intercom call. Defaults to 1.

Intercom Barge

Boolean, Defaults to 1

If disabled, the phone will not allow an Intercom call to barge in over an already-in-progress call. Defaults to 1.

Use Auto Redial

Boolean, Defaults to 0

If enabled, when the user calls a busy number, the phone will offer a pop-up to continue dialing the destination according to AutoRedialDelay and AutoRedialTimes. Defaults to 0.

AutoRedial Delay

Integer, in seconds, Defaults to 10

Sets the delay, in seconds, the phone should make between AutoRedialTimes if UseAutoRedial is enabled and has been called by the user. Defaults to 10.

AutoRedial Times

Integer, Defaults to 10

Sets the number of times the phone should attempt to automatically redial a busy number. Defaults to 10.

Call Complete

Boolean, Defaults to 0

If enabled, the phone will, upon transitioning from having called a Busy party back to the idle state, provide a pop-up allowing the user to dial the busy party again, or cancel. Defaults to 0.

Hide DTMF Type

Integer, 0-3, Defaults to 0

Sets the type of DTMF hiding on the onscreen display:

Display all input - 0
Hide all input using a * character - 1
As digits are entered, change them to a * character after a small delay - 2
Display only the last digit properly, but other digits as a * character - 3

Talk DTMF Tone

Boolean, Defaults to 1

If disabled, local DTMF playback of tones will not be heard while the phone is on a call. Defaults to 1.

Dial DTMF Tone

Boolean, Defaults to 1

If disabled, local DTMF playback of tones will not be heard while the phone is dialing. Defaults to 1.

Psw Dial Mode

Boolean, Defaults to 0

If enabled, the phone will disguise, on-screen, dialed DTMF using * characters. Defaults to 0.

Psw Dial Length

Integer, Defaults to 0

Sets the number of digits that should be disguised if PswDialMode is enabled. Digits entered after PswDialLength is reached in length will not be disguised. Defaults to 0.

Psw Dial Prefix

String

Sets a dialing prefix that, if dialed, and if PswDialMode is enabled, will disguise, on-screen, dialed DTMF using * characters.

Enable MultiLine

Boolean, Defaults to 1

If enabled, the phone will allow up to 10 incoming calls. If disabled, the phone will only allow up to 2 incoming calls. Defaults to 1.

Allow IP Call

Boolean, Defaults to 1

If disabled, the phone will not be able to perform direct IP dialing. Defaults to 1.

CHolding Tone

Boolean, Defaults to 1

If disabled, the phone will not play a periodic tone when a call has been left on hold for more than 30 seconds. Defaults to 1.

Number Privacy

Boolean, Defaults to 0

If enabled, follows the defined Privacy Rule in order to disguise digits. Defaults to 0.

Privacy Rule

String

Sets the privacy rule to apply to Number Privacy number disguising where:

X defines the first number disguised

• defines a number to be disguised

. defines the last number to be disguised 

ID

P[n]

The identifier for the rule

rule

String

The code plan rule

ID

String

Identifier beginning with "Item1" and continuing with "Item2", "Item3" etc.

rule

String

Defines the digit mapping string as per https://wiki.asterisk.org/wiki/display/DIGIUM/Dial+Plans

Signal Standard

Integer, Defaults to 11

Sets the tone standard that the phone should apply as follows:

Australia - 15
Belgium - 0
Brazil - 16
China - 1
Czech - 12
Germany - 2
Israel - 3
Italy - 21
Japan - 4
Netherlands - 5
Norway - 6
South Africa - 14
South Korea - 7
Spain - 22
Sweden - 8
Switzerland - 9
Chinese Taiwan - 10
United Kingdom - 13
United States - 11 

Enable MWI Tone

Boolean, Defaults to 1

If disabled, the phone will not play back a tone when receiving a new message and activating MWI. Defaults to 1.

Play Egress DTMF

Integer, 0-2, Defaults to 2

If set to 0, the phone will not play back local tones when tones are received from the remote party. If set to 1, the phone will play back the INFORM tone when any tone is received from the remote party. If set to 2, the phone will play back the corresponding DTMF tone as received from the remote party. Defaults to 2.

Onhook Time

Time in milliseconds, Defaults to 120

Sets the on-hook debounce timer. Defaults to 120.

G729 Payload Len

Integer, 0-5, Defaults to 1

Sets the G.729 payload length as follows:

10ms - 0
20ms - 1
30ms - 2
40ms - 3
50ms - 4
60ms - 5

Defaults to 1 

G723 Bit Rate

Integer, Defaults to 1

Sets the bitrate type to be used for G.723.1 voice codec encoding. 0 sets encoding to 5.3kbit/s. 1 sets encoding to 6.3kbit/s. Defaults to 1

G722 Timestamps

Integer, Defaults to 0

Sets the timestamp difference between G.722 packets. If set to 0, voice packets are sent every 20ms and the time-stamp increases 160 between each packet. If set to 1, voice packets are sent every 20s and the time-stamp increases 320 between each packet.

VAD

Boolean, Defaults to 1

If enabled, while the phone is using PCMU or PCMA coding, provide a prompt over the handset after a quiet period, to indicate that the call is ongoing.

Ring Type

Integer, 1-9, Defaults to 2.

Sets the ringing type of the phone from 1-9. Defaults to 2.

Dtmf Payload Type

Integer, 96-127. Defaults to 101

Sets the RTP payload type to be used for RFC2833 DTMF events. Defaults to 101.

TX AGC

Integer, Defaults to 0

Sets the transmit analog gain. Defaults to 0.

RX AGC

Integer, Defaults to 0

Sets the receive analog gain. Defaults to 0.

Headset MIC offset

Integer, 1-8. Defaults to 3

Sets the headset microphone gain offset as follows:

-12dB, 1
-9dB, 2
-6dB, 3
-3dB, 4
0dB, 5
3dB, 6
6dB, 7
9dB, 8

Defaults to 3. 

Headset spkr offset

Integer, 1-8, Defaults to 7

Sets the headset receiver volume offset as follows:

-12dB, 1
-9dB, 2
-6dB, 3
-3dB, 4
0dB, 5
3dB, 6
6dB, 7
9dB, 8

Defaults to 7. 

Sidetone GAIN

Integer, 0-9, Defaults to 1

If set to 0, eliminates sidetone. Higher values provider higher levels of sidetone. Defaults to 1.

EHS Type

Integer, 0-1, Defaults to 0

If set to 0, no EHS is enabled. If set to 1, EHS type for Plantronics is enabled.

RTP Keep Alive

Boolean, Defaults to 0

If enabled, the phone will send periodic RTP keep alive packets. Defaults to 0.

Session Report

Boolean, Defaults to 0

If enabled, the phone will send RTCP-XR Session Reports.

Interval Report

Boolean, Defaults to 0

If enabled, the phone will send RTCP-XR Interval Reports.

Interval Period

Integer, in seconds, 5-99, Defaults to 60

Sets the interval period at which the phone sends RTCP-XR reports. Defaults to 60.

MOS-LQ Warning

Integer, 15-40, Defaults to 40

Sets the warning threshold for MOS-LQ

MOS-LQ Critical

Integer, 15-40, Defaults to 25

Sets the critical threshold for MOS-LQ

Delay Warning

Integer, in milliseconds, 10-2000, Defaults to 150

Sets the warning threshold for Delay. Defaults to 150.

Delay Critical

Integer, in milliseconds, 10-2000, Defaults to 200

Sets the critical threshold for Delay. Defaults to 200.

Phone Report

Boolean, Defaults to 0

If enabled, displays reports on the phone.

WEB Report

Boolean, Defaults to 0

If enabled, displays reports in the phone's web interface.

ID

P1

Sets the port to which the config applies; always set to P1.

General Spk Vol

Integer, 1-9, Defaults to 5

Sets the default call volume. Defaults to 5.

General Mic Vol

Integer, 1-9, Defaults to 3

Sets the default microphone volume. Defaults to 3.

Headset Vol

Integer, 1-9, Defaults to 5

Sets the default headset volume. Defaults to 5.

Ring in Headset

Boolean, Defaults to 0

If enabled, play ringing tone out the headset port instead of the loudspeaker. Defaults to 0.

Auto Headset

Boolean, Defaults to 0

If enabled, answered calls will answer to the headset, not to the handset (unless lifted) or loudspeaker. Defaults to 0.

Headset Ring Vol

Integer, 1-9, Defaults to 5

Sets the default headset ringing volume. Defaults to 5.

HandFree Vol

Integer, 1-9, Defaults to 5

Sets the default handsfree / speakerphone volume. Defaults to 5.

RingTone Vol

Integer, 0-9, Defaults to 5

Sets the default ringing volume. Defaults to 4.

Voice Codec1

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the first-offered codec. Defaults to G722/8000.

Voice Codec2

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the second-offered codec. Defaults to PCMA/8000.

Voice Codec3

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the third-offered codec. Defaults to PCMU/8000.

Voice Codec4

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the fourth-offered codec. Defaults to G729/8000.

Voice Codec5

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the fifth-offered codec.

Voice Codec6

G722/8000, PCMA/8000, PCMU/8000, G729/8000, G723/8000, G726/8000

Sets the sixth-offered codec.

ID

Alert[n] where n=1-10

Sets an identifier for the Alert. Up to 10 Alerts may be defined.

Text

String

Specifies the text of the Alert-Info header that should be acted on for this alert.

Ring Type

Integer, 1-9

Specifies the phone ringing type to apply for this Alert.

SIP Port

Integer, 1-65535, Defaults to 5060

Sets the local SIP signaling port used by the phone. Defaults to 5060

STUN Server

IPv4 Address or Hostname

Sets the IPv4 Address or Hostname of the STUN server.

STUN Port

Integer, 1-65535, Defaults to 3478

Sets the port of the STUN server. Defaults to 3478.

STUN Refresh Time

Integer, in seconds, Defaults to 50

Sets the STUN server refresh time, at which the phone will send a binding request period. Defaults to 50.

SIP Wait Stun Time

Integer, in milliseconds, Defaults to 800

Sets the amount of the, in milliseconds, the phone should wait for the STUN server to respond before continuing. Defaults to 800.

Extern NAT Addrs

IPv4 Address

If the phone is configured to use STUN, the SIP Contact address will be set according to this option.

Reg Fail Interval

Integer, in seconds, Defaults to 32.

Sets the time, after a failed registration, after reaching the halfway point of this interval time, at which the phone will attempt registration again. Defaults to 32.

SIP Pswd Encryption

Boolean, Defaults to 0

If enabled, the phone's configuration file will be encrypted. Defaults to 0.

Strict BranchPrefix

Boolean, Defaults to 0

If enabled, when the phone receives a SIP message with a branch field that does not begin with z9hG4bk, the phone will return a 4xx message. Defaults to 0

Enable Group Backup

Boolean, Defaults to 0

If enabled, and the phone has both regular and backup registrars configured, the phone will, upon a failure to register with either of the registrars, unregister from both. If disabled, the phone will attempt to register with both, and the registration of one will not affect the registration with another. Defaults to 0.

Enable RFC4475

Boolean, Defaults to 1

If enabled, and the phone receives a SIP message with a From or To field containing a blank space, quotation marks, or both, the phone will reject the message. Defaults to 1.

SIP invite strict

Boolean, Defaults to 1

If disabled, the phone will allow SIP requests from servers to which it is not registered. Defaults to 1.

Notify Reboot

Boolean, Defaults to 0

If disabled, the phone will not reboot when receiving a check-sync NOTIFY. Defaults to 0.

SMS direct Enabled

Boolean, Defaults to 0

If enabled, the phone will display the details of a text message when a new message is received.

SMS Save Enabled

Boolean, Defaults to 1

If disabled, the phone will not save received text message.

SMB Ring Enabled

Boolean, Defaults to 1

If disabled, the phone will not play a ringing tone when receiving an incoming text message.

CSTA Enable

Boolean, Defaults to 0

If enabled, the phone will be controllable using uaCSTA. Defaults to 0.

ID

SIP1, SIP2
SIP3, SIP4 (A25-only)

Sets the SIP line (1-4) to which the configuration settings should be applied.

Phone Number

String

Sets the identifier used for the user part of the From and To lines in the phone's SIP messaging.

Display Name

String

Sets the quoted string name identifier used in the From and To (REGISTER only) in the phone's SIP messaging.

Sip Name

String

Sets a name for the SIP line, visible within the web admin UI of the phone.

Register Addr

IPv4 Address or Hostname

Sets the IPv4 address or hostname of the SIP Registrar.

Register Port

Integer, 1-65535, Defaults to 5060

Sets the port used to contact the SIP Registrar. Defaults to 5060

Register User

String

Sets the SIP authentication user.

Register Pswd

String

Sets the SIP authentication password.

Register TTL

Integer, in seconds, Defaults to 3600

Sets the default Expires timer for SIP registration. Defaults to 3600.

Enable Reg

Boolean, Defaults to 0

Enables or disables SIP registration for this line.

Proxy Addr

IPv4 Address or Hostname

Sets the IPv4 address or hostname for the SIP proxy. Defaults to none.

Proxy Port

Integer, 1-65535, Defaults to 5060

Sets the port used to contact the SIP Proxy. Defaults to 5060.

Proxy User

String

Sets the SIP proxy authentication user.

Proxy Pswd

String

Sets the SIP proxy authentication password.

BakProxy Addr

IPv4 Address or Hostname

Sets the IPv4 address or hostname for the backup SIP Proxy. Defaults to none.

BakProxy Port

Integer, 1-65535, Defaults to 5060

Sets the port used to contact the backup SIP Proxy. Defaults to 5060.

Enable Failbac

Boolean, Defaults to 0

Sets whether the phone, whereby it is configured with both a primary and a backup proxy, should, whereupon detection that the primary proxy is operational again after having previously failed, resume sending calls to the primary server. If enabled, the phone will switch back to the primary proxy. If disabled, the phone will continue to send calls to the backup. Defaults to 0.

Signal Crypto

Boolean, Defaults to 0

If enabled, causes the phone to encrypt SIP signaling. Defaults to 0.

SigCrypto Key

String

Sets the key used to encrypt SIP signaling.

Media Crypto

Boolean, Defaults to 0

If enabled, causes the phone to encrypt RTP media. Defaults to 0.

MedCrypto Key

String

Sets the key used to encrypt RTP media.

SRTP Auth-Tag

Integer, Defaults to 0

If set to 0, the phone will utilizes 80 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_80. If set to 1, the phone will utilize 32 byte SRTP tags, encrypting RTP using AES_CM_128_HMAC_SHA_32. Defaults to 0.

Local Domain

String

Sets the domain name used in SIP registration.

Always FWD

Boolean, Defaults to 0

If enabled, the phone will unconditionally forward calls. Defaults to 0.

Busy FWD

Boolean, Defaults to 0

If enabled, the phone will forward calls whenever it is busy. Defaults to 0.

No Answer FWD

Boolean, Defaults to 0

If enabled, the phone will forward calls that are not answered. Defaults to 0.

Always FWD Num

String

Sets the forwarding number used in conjunction with the Always FWD option.

Busy FWD Num

String

Sets the forwarding number used in conjunction with the Busy FWD option.

NoAnswer FWD N

String

Sets the forwarding number used in conjunction with the No Answer FWD option.

FWD Timer

Integer, in seconds, Defaults to 5

Sets the time, in seconds, applied to the No Answer FWD option. Defaults to 5.

Ring Type

Integer, 0-9, Defaults to 0

Sets the ring type. If 0, use the default ring type. Otherwise, use the assigned ringing type tones. Defaults to 0.

Hotline Num

String

Sets the number to be dialed when the off-hook time is greater than the WarmLine Time and Enable Hotline is enabled.

Enable Hotline

Boolean, Defaults to 0

If enabled, and the phone has been off-hook longer than the WarmLine_Time, the phone will automatically dial the number defined by Hotline Num.

WarmLine Time

Integer, in seconds, 0-9, Defaults to 0

Sets the amount of time the phone must remain off-hook before attempting to execute Hotline functionality.

Pickup Num

String

Sets the dialing prefix applied to calls that are picked up using function keys configured for Pickup functionality.

Join Num

String

Sets the dialing prefix applied to calls that are joined using function keys configured for Join functionality.

NAT UDPUpdate

Integer, 0-2, Defaults to 2

If set to 1, the phone will send SIP OPTION packets to the server after each UDPUpdate TTL time. If set to 2, the phone will send a CRLF to the server after each UDPUpdate TTL time. If set to 0, the phone will send nothing. Defaults to 2.

UDPUpdate TTL

Integer, in seconds, Defaults to 30

Sets the timer used by the NAT UDPUpdate option.

Server Type

0, 1, 6, 14, 17, 22, 23, 24, 26, 28, 29, 30, 31, 33. Defaults to 0

Sets special compatibility settings required for specific server types. The following types are supported:

3CX - 31
BOTE - 6
BroadSoft - 28
Cellcom - 30
COMMON - 0
CONFIG - 23 
Epygi - 33
FUJITSU - 24
Karel UCAP - 29
MITEL - 17
MS_RP - 22
NET2PHONE - 1
NORTEL - 14
SOFTX3000 - 26

Defaults to 0. 

User Agent

String

Sets the SIP User-Agent passed by the phone when communicating.

PRACK

Boolean, Defaults to 1

Enables or disables SIP PRACK functionality within the phone. Defaults to 1.

Keep AUTH

Boolean, Defaults to 0

If enabled, the phone will, on SIP re-registration, send authentication in the initial REGISTER rather than waiting to send it after receiving a 401 Unauthorized message. Defaults to 0.

Session Timer

Boolean, Defaults to 0

If enabled, the phone will send SIP session timers throughout the call, ending the call when there is no reply. Defaults to 0.

S.Timer Expire

Integer, in seconds, Defaults to 0

Sets the SIP Session timer timeout value in seconds. Defaults to 0

Enable GRUU

Boolean, Defaults to 0

If enabled, the phone will append GRUU information to the Contact header of INVITEs. Defaults to 0.

DTMF Mode

Integer, 0-3, Defaults to 3

Sets the DTMF method to be used by the phone, as follows:

Inband - 0
RFC2833 - 1
SIP INFO - 2
Auto - 3 

Defaults to 3.

DTMF Info Mode

Integer, 0-1, Defaults to 0

If set to 1, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send "*" and "#" respectively. If set to 0, and the phone is configured for SIP INFO DTMF, the * and # keypresses will send as 10 and 11 respectively. Defaults to 0.

NAT Type

Boolean, Defaults to 0

If enabled, STUN will be used. Defaults to 0.

Enable Rport

Boolean, Defaults to 1

If disabled, the phone will not send rport to assist with NAT traversal as per RFC3581. Defaults to 1.

Subscribe

Boolean, Defaults to 0

If enabled, the phone will subscribe for Message Waiting Indicator (MWI). Defaults to 0.

Sub Expire

Integer, in seconds, Defaults to 3600

The timer at half-of-which, the phone will re-subscribe. Defaults to 3600.

Single Codec

Boolean, Defaults to 0

If enabled, the phone will respond to SIP messages with only one codec, rather than with all codec capabilities. Defaults to 0.

CLIR

Integer, 0-2, Defaults to 0

Specifies the method of anonymous calling to use. When set to 0, the phone calls normally. When set to 1, the phone calls anonymously according to RFC3323. When set to 2, the phone calls anonymously according to RFC3325.

Strict Proxy

Boolean, Defaults to 0

When enabled, respond using the source address, not the Via address. Defaults to 0.

Direct Contact

Boolean, Defaults to 0

When enabled, attempt to directly communicate with the called party, not using the intermediary proxy or UA. Defaults to 0.

History Info

Boolean, Defaults to 0

When enabled, call history information for the line will be provided. Defaults to 0. This configuration item is currently unused.

DNS SRV

Boolean, Defaults to 0

If enabled, the phone will perform DNS SRV resolution for outgoing requests. Defaults to 0.

DNS Mode

Integer, 0-2, Defaults to 0

Sets the type of host resolution to perform. When set to 0, the phone will use A records. When set to 1, the phone will use SRV records. When set to 2, the phone will use NAPTR records.

XFER Expire

Integer, in seconds, Defaults to 0

Specifies the time, in seconds, after which the phone will send a BYE following attended transfer hang up.

Ban Anonymous

Boolean, Defaults to 0

When enabled, the phone will reject anonymous calls. Defaults to 0.

Dial Off Line

Boolean, Defaults to 0

If enabled, the phone will attempt to place outgoing calls, even when it is unregistered. If disabled, the phone will not be able to place outgoing calls when it is unregistered. Defaults to 0.

Quota Name

Boolean, Defaults to 0

If enabled, the phone will encapsulate the Display Name that it sends in SIP signaling inside of quotation marks. Defaults to 0.

Presence Mode

Boolean, Defaults to 0

When enabled, the phone utilizes special presence handling for Wuchuan servers. Defaults to 0.

RFC Ver

Integer, 0-1, Defaults to 1

Specifies the SIP signaling RFC standard to utilize. When set to 0, the phone will communicate using RFC2543 compliant signaling. When set to 1, the phone will communicate using RFC3261 compliant signaling. Defaults to 1.

Signal Port

Integer, Defaults to 5060

Sets the phone's local SIP signaling port. Defaults to 5060.

Transport

Integer, 0, 1, 3, Defaults to 0

Sets the transport type for SIP signaling.
UDP - 0
TCP - 1
TLS - 3

Enable ChgPort

Boolean, Defaults to 1

If enabled, the phone will attempt to dynamically change its local SIP port in order to work around SIP Router ALG issues. Defaults to 1.

TLS Version

Integer, 0-2, Defaults to 0

Sets the type of TLS protocol version to be used:

TLS 1.0 - 0
TLS 1.1 - 1
TLS 1.2 - 2 

Defaults to 0.

Use SRV Mixer

Boolean, Defaults to 0

When enabled, the phone utilizes server-side conferencing support. Defaults to 0.

SRV Mixer Uri

String

Sets the URI to be used for server-side conferencing when the Use SRV Mixer option is enabled.

Long Contact

Boolean, Defaults to 0

If enabled, allows the phone to process long Contact fields. Defaults to 0.

Auto TCP

Boolean, Defaults to 0

When enabled, if the packet size of a UDP signaling packet is to exceed 1300 bytes, automatically use TCP transport. Defaults to 0.

Uri Escaped

Boolean, Defaults to 1

If disabled, the phone will not escape # characters into "%23" when creating URIs. While this option is enabled, the rule to send numbers when pressing the # key should be disabled.

Click to Talk

Boolean, Defaults to 0

If enabled, the phone can make a call by itself receiving an incoming REFER message. Defaults to 0.

MWI Num

String

Sets the number to dial for voicemail.

CallPark Num

String

Sets the number to dial for call parking.

Retrieve Num

String

Sets the number to dial for call retrieval for Broadsoft environments.

MSRPHelp Num

String

For MS_RP_BU servers, sets a number to be called after a successful transfer.

User Is Phone

Boolean, Defaults to 1

If disabled, the phone will not append the ";user=phone" parameter to SIP messages.

Auto Answer

Boolean, Defaults to 0

If enabled, and if the NoAnswerTime has elapsed, the phone will automatically answer an incoming call. Defaults to 0.

NoAnswerTime

Integer, in seconds, defaults to 5

Sets the amount of time, in seconds, the phone should wait on an incoming call before proceeding to Auto Answer, if Auto Answer is enabled. Defaults to 5.

MissedCallLog

Boolean, Defaults to 1

If disabled, the phone will not record call logs. Defaults to 1.

SvcCode Mode

Boolean, Defaults to 0

If enabled, the phone will allow the sending of service codes (numbers) to the SIP server, depending on the enabling/disabling of certain functions on the phone. Defaults to 0.

DNDOn SvcCode

String

Sets the number to send to the server when DND is enabled on the phone.

DNDOff SvcCode

String

Sets the number to send to the server when DND is disabled on the phone.

CFUOn SvcCode

String

Sets the number to send to the server when Call Forward Unconditional is enabled on the phone.

CFUOff SvcCode

String

Sets the number to send to the server when Call Forward Unconditional is disabled on the phone.

CFBOn SvcCode

String

Sets the number to send to the server when Call Forward Busy is enabled on the phone.

CFBOff SvcCode

String

Sets the number to send to the server when Call Forward Busy is disabled on the phone.

CFNOn SvcCode

String

Sets the number to send to the server when Call Forward on No Answer is enabled on the phone.

CFNOff SvcCode

String

Sets the number to send to the server when Call Forward on No Answer is disabled on the phone.

ANCOn SvcCode

String

Sets the number to send to the server when Anonymous Call Banning is enabled on the phone.

ANCOff SvcCode

String

Sets the number to send to the server when Anonymous Call Banning is disabled on the phone.

Send ANOn Code

String

Sets the number to send to the server when Anonymous Calling is enabled on the phone.

Send ANOffCode

String

Sets the number to send to the server when Anonymous Calling is disabled on the phone.

CW On Code

String

Sets the number to send to the server when Call Waiting is enabled on the phone.

CW Off Code

String

Sets the number to send to the server when Call Waiting is disabled on the phone.

VoiceCodecMap

Comma-separated list of:
G722, G711U, G711A, G729, G726-32, G723

Sets the voice codecs used for this line.

BLFList Uri

String

Specifies the BLF Resource List to which the phone should subscribe. Multiple lists are supported, separated by commas.

BLF Server

IPv4 Address or Hostname

If the server to which the phone is registered does not support BLF Resource List subscription package, sets the address of the BLF Resource List server.

Respond 182

Boolean, Defaults to 0

If enabled, the phone will, when it's already on call and an additional call comes in, send a 182 Queued SIP message to the SIP server. If disabled, the phone sends a 180. Defaults to 0.

Enable BLFList

Boolean, Defaults to 0

If enabled, the phone will subscribe for BLF Resource List.

Caller Id Type

Integer, 1-5, Defaults to 4

Sets the priority of the incoming Caller ID:
FROM header - 1
P-Asserted-Identity header, followed by FROM header - 2
Remote-Party-ID header, followed by FROM header - 3
P-Asserted-Identity header, followed by Remote-Party-ID header, followed by FROM header - 4
Remote-Party-ID header, followed by P-Asserted-Identity-Header, followed by FROM header - 5

Syn Clock Time

Boolean, Defaults to 0

If enabled, the phone will set its clock according to the Date field in the 200 OK following a successful REGISTER. Defaults to 0.

Use VPN

Boolean, Defaults to 1

If disabled, and the phone is connected to a VPN, the phone will not initiate REGISTER using the VPN IP address. If enabled, the phone will, when connected to a VPN, use the VPN IP address to initiate the REGISTER. Defaults to 1.

Enable DND

Boolean, Defaults to 0

If enabled, the phone will not accept incoming calls from this SIP line. Defaults to 0.

Update Reg Exp

Boolean, Defaults to 1

If disabled, the phone will not update its registration expiration with the Expires value from the 200 OK that the server sends in response to a successful registration. Defaults to 1.

Inactive Hold

Boolean, Defaults to 0

If enabled, the phone will send "a=inactive" in the INVITE sent after a call is placed on hold. If disabled, the phone will send "a=sendonly" in the INVITE sent after a call is placed on hold. Defaults to 0.

Enable SCA

Boolean, Defaults to 0

Enables support for the Broadsoft SCA feature. Defaults to 0.

Sub CallPark

String, Defaults to 0

Sets the Call Parking subscribed number for Broadsoft servers. Defaults to 0.

Hoteling Event

Boolean, Defaults to 0

If enabled, subscribes for Broadsoft Hotel agent service. Defaults to 0.

Sub CC Status

Boolean, Defaults to 0

If enabled, subscribes to the Broadsoft call center service. Defaults to 0.

CSTA Number

String

Sets the number/URI for the uaCSTA server.

Feature Sync

Boolean, Defaults to 0

Enables support for Broadsoft Feature Sync. Defaults to 0.

Req With Port

Boolean, Defaults to 1

If disabled, do not send port in SIP messages to the server. Defaults to 1.

Enable Mute

Boolean, Defaults to 0

If enabled, mutes the phone during intercom calls. Defaults to 0.

VQ Name

String

Sets an identifier for the voice quality server.

VQ Server

IPv4 Address or Hostname

Sets the IPv4 Address or hostname of the voice quality server.

VQ Server Port

Integer, 1-65535, Defaults to 5060

Sets the port used by the voice quality server.

VQ HTTP Server

URL

Sets the HTTP URL of the voice quality server.

Unreg Reboot

Boolean, Defaults to 0

If enabled, the phone will send unregisters to any registered servers after it reboots, before it attempts to register. Defaults to 0.

Flash Mode

Integer, 0-1, Defaults to 0

If set to 0, flash is handled locally on the phone. If set to 1, the phone will send a SIP INFO message indicating the flash event to the server, with data defined by Content Type and Content Body

Use Tel Call

Boolean, Defaults to 0

If enabled, the phone will replace "sip" in its URIs with "tel"

Content Type

String

Sets the content type data used when the phone sends SIP INFO flash messages to the server.

Content Body

String

Sets the body of the data used when the phone sends SIP INFO flash messages to the server.

Deal 180

Boolean, Defaults to 0

If disabled, the phone will not generate local ringback on 180, instead depending on inband RTP ringback provided by the remote party.

Priority

Integer, 0-10, Defaults to 0

Sets the priority value at which normal calls should take precedence over multicasted audio calls. At 0, normal calls will take priority over any multicasted calls. At 1, normal calls are lower priority than multicast priority 1 calls, but higher priority than any other multicast priority levels. Additional values follow the same logic. Defaults to 0.

Enable Priority

Boolean, Defaults to 0

If enabled, the phone will sort multicast audio by priority, allowing one multicast audio stream to take precedence over another multicast audio stream. Defaults to 0.

ID

MCAST[n], where n=1-10

Sets an identifier for the Multicast listener. Up to 10 are supported.

Port

Integer, 1-65535, Defaults to 0

Sets the port for this multicast listener.

Name

String

Sets the name to be displayed on the phone's screen when audio from this multicast listener is played back.

Host

IPv4 Multicast address

Sets the IPv4 multicast address for this listener.

PPPoE User

String

If the phone is to use PPPoE authentication, sets the PPPoE authentication username.

PPPoE Password

String

If the phone is to use PPPoE authentication, sets the PPPoE authentication password.

PPPoE Svc Name

String, Defaults to ANY

Sets the PPPoE server name. Defaults to ANY.

PPPoE IP Address

IPv4 Address

Sets the IPv4 Address of the PPPoE server.

Web Port

Integer, 1-65535, Defaults to 80

Sets the port for the phone's built-in web server. Defaults to 80.

Web Server Type

Integer, 0-1, Defaults to 0

If set to 1, the phone will permit access to its configuration web pages using HTTPs, instead of HTTP. Defaults to 0.

Https Web Port

Integer, 1-65535, Defaults to 443

Sets the port for the phone's rebuilt in HTTPs web server. Defaults to 443.

Enable MMI Filter

String

If enabled the phone will not permit web configuration from any device not in the filter list. The filter list is a

Web Authentication

Integer, 0-1, Defaults to 0

If set to 1, the phone utilizes basic auth instead of digest auth. Defaults to 0.

Default Web User

Integer 0-2, Defaults to 0

Sets the default web user login type as follows:

None - 0
User - 1
Administrator - 2

Defaults to 0 

ID

Item[n]

Sets an identifier for the filter

First IP

IPv4 Address

Sets the first IP address to which this filter applies.

End IP

IPv4 Address

Sets the last IP address to which this filter applies.

ID

Account[n]

Sets an identifier for the web account.

Name

String

Sets the username for this account.

Password

String

Sets the password for this account.

Level

Integer, 5, 10

Sets the access level for this account. 5 for users, 10 for administrators.

Enable VLAN

Boolean, Defaults to 0

If enabled, the phone will perform VLAN assignment of itself and its PC port.. Defaults to 0.

Enable diffServ

Boolean, Defaults to 1

If enabled, the phone will perform DSCP tagging. Defaults to 1.

LLDP Transmit

Boolean, Defaults to 1

If disabled, the phone will not transmit LLDP packets to the switch. Defaults to 1.

LLDP Refresh Time

Integer, in seconds, Defaults to 60

Sets the interval, in seconds, at which the phone will transmit LLDP packets. Defaults to 60.

LLDP Learn Policy

Boolean, Defaults to 1

If disabled, the phone will not learn its VLAN settings using LLDP-MED TLV. Defaults to 1.

CDP Enabled

Boolean, Defaults to 0

If enabled, the phone will send CDP packets. Defaults to 0.

CDP Refresh Time

Integer, in seconds, Defaults to 60

Sets the period at which CDP packets will be sent from the phone.

Singalling DSCP

Defaults to -1

Sets the DSCP value for SIP signaling. Defaults to -1.

Voice DSCP

Integer, Defaults to 46

Sets the DSCP value for RTP media. Defaults to 46.

VLAN ID

Integer, 0-4095, Defaults to 256

Sets the VLAN ID to which the phone should bind itself. Defaults to 256.

Signalling Priority

Integer, 0-7. Defaults to 0.

Sets the 802.1p COS bit for SIP Signaling. Defaults to 0.

Voice Priority

Integer, 0-7. Defaults to 0.

Sets the 802.1p COS bit for RTP Media. Defaults to 0.

VLAN Recv Check

Boolean, Defaults to 1

If enabled, the phone will compare the VLAN ID of LAN port packets and will not process them if they match the PC port packets. Defaults to 1.

Enable PVID

Boolean, Defaults to 1

If enabled, the phone will tag the PC port with the VLAN assigned by PVID Value. Defaults to 1.

PVID Value

Integer, 0-4095. Defaults to 254.

Sets the PC port VLAN ID. Defaults to 254.

DHCP Option Vlan

Integer, Defaults to 0

If set to 0, the phone will not retrieve its VLAN from DHCP. If set to an option, 128-254, the phone will respond to the named DHCP Option.

MGR Trace Level

Defaults to 0

Sets the MGR trace level. Defaults to 0.

SIP Trace Level

Defaults to 0

Sets the SIP trace level. Defaults to 0.

Trace File Info

Boolean, Defaults to 0

Displays line numbers in the trace file. Defaults to 0.

Enable Watch Dog

Boolean, Defaults to 1

If disabled, the phone will not restart if it experiences an application crash. Defaults to 1.

Enable Memory Info

Boolean, Defaults to 0

If enabled, the phone will report memory status to look for leaks. Defaults to 0.

Enable Syslog

Boolean, Defaults to 0

If enabled, will output debug information to a remote syslog server defined by Syslog address and Syslog port

Syslog address

IPv4 Address

Specifies the IPv4 address of a remote syslog server.

Syslog port

Integer, 0-4095, Defaults to 514

Specifies the port of the remote syslog server.

Enable In Access

Boolean, Defaults to 0

If enabled, remoter servers cannot access the phone, but the phone can contact them. Defaults to 0.

Enable Out Access

Boolean, Defaults to 0

If enabled, the phone cannot access remote servers, but can be contacted by them. Defaults to 0.

Menu Password

Integer, Defaults to 789

Sets the password used to access the phone's password-protected advanced menu setting. Defaults to 789.

KeyLock Password

Integer, Defaults to 123

Sets the password used to unlock the phone when key lock has been engaged

Fast Keylock Code

Integer

Sets a key sequence that, when entered, immediately locks the phone.

Enable KeyLock

Boolean, Defaults to 0

If enabled, allows locking of the phone. Defaults to 0.

KeyLock Status

0, 1

Displays the phone's locked status. 0 for unlocked, 1 for locked.

Emergency Call

String

Sets a number the phone is allowed to call, even while locked.

LCD Title

String, Defaults to Asterisk

Sets the text displayed in the idle screen status bar. Defaults to Asterisk

LCD Constrast

Integer, 1-10, Defaults to 5

Sets the display's contrast level. Obsolete.

LCD Luminance

Boolean, Defaults to 1

If disabled, the phone's backlight will not be list. Defaults to 1.

Backlight Off Time

Integer, in seconds, Defaults to 30

Sets the time, in seconds, at which the phone will turn its backlight off. Defaults to 30. SUGGEST A LONGER TIME, E.G. 15 MINUTES

ScrnSaver Wait Time

Integer, in seconds, Defaults to 0

Sets the time, zero is off, at which the screensaver will engage. Defaults to 0.

KeyLock Timeout

Integer, in seconds, Defaults to 0

If greater than 1, sets a timer that, when reached, causes the phone to automatically lock its keypad.

Enable Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when idle, flash red on incoming calls, and flash slowly on missed calls / waiting messages. Defaults to 0.

SMS MWI Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when a new MESSAGE has been received. Defaults to 0.

Miss Call Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when a missed call is received. Defaults to 0.

Talk Dial Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when the phone is on a call. Defaults to 0.

Ringing Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when the phone is ringing. Defaults to 0.

Mute Call Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when the phone is muted. Defaults to 0.

Hold Power Led

Boolean, Defaults to 0

If enabled, the MWI LED will turn on when a caller is placed on hold. Defaults to 0.

Time Display Style

Integer, 0-1, Defaults to 0

When 0, display time in 24-hour format. When 1, display time in 12-hour format. Defaults to 0. SUGGEST DEFAULTING TO 12-HOUR

Phone Model

String, Defaults to A20, A22 or A25

Shows the phone model. Defaults to A20, A22 or A25

FuncKey Page Num

Integer, Defaults to 1

Specifies the number of pages of BLF keys that the phone is to display. Defaults to 1.

Blf Default type

Integer, 0-2, Defaults to 0

Sets the default transfer function of the BLF keys:

None - 0
Blind - 1
Attended - 2 

Alarm Clock

0,,1

Enables the alarm clock. The default value is 0,,1

Disable CHN IME

Boolean, Defaults to 0

Enables preventing Chinese Input methods. Defaults to 0.

Disable Dial Search

Boolean, Defaults to 0

If enabled, prevents searching and number matching during dialing. Defaults to 0.

Redial Enter Clog

Integer, 0-1, Defaults to 1

If set to 0, the redial button will dial the last number dialed. If set to 1, the phone will enter the call log and display recently dialed numbers. Defaults to 1.

Date Display Style

Integer, 0-13, Defaults to 0

Sets the date display formatting that should be used by the phone as follows:

1 JAN MON - 0
JAN 1 MON - 1
MON 1 JAN - 2
MON JAN 1 - 3
DD MM YY - 4
DD MM YYYY - 5
MM DD YY - 6
MM DD YYYY - 7
YY MM DD - 8
YYYY MM DD - 9
1 January Monday - 10
January 1 Monday - 11
Monday 1 January - 12
Monday January 1 - 13 

Date Separator

Integer 0-3, Defaults to 0

Sets the date display separator that should be used by the phone as follows:

/, 0
-, 1
., 2
(space character), 3 

Enable Pre-Dial

Boolean, Defaults to 1

If disabled, the phone will go off-hook as soon as DTMF is entered, and off-hook dialing rules will be active. Defaults to 1.

Default Line

Integer, 0-1 or 0-3 (A25), Defaults to 0.

Sets the line which the phone will, by default, use for outbound calling. Defaults to 1.

Enable Default Line

Boolean, Defaults to 0

If enabled, show, while the phone is idle, in the phone's greeting / status bar, the default line that will be used. Defaults to 0.

Enable Auto SelLine

Boolean, Defaults to 1

If disabled, do not automatically switch from an unregistered default line to a registered other line for outgoing calls. Defaults to 1.

Agent Username

String

Sets the Broadsoft agent username.

Agent Password

String

Sets the Broadsoft agent password.

Agent Number

String

Sets the Broadsoft agent number.

Agent Sipline

Integer, 0-1 or 0-4 (A25), Defaults to 0

Sets the SIP line for Broadsoft agent login.

Agent Status

Integer, 0-4, Defaults to 0

Sets the Broadsoft agent status as follows:

LOGON - 0
LOGOFF - 1
UNAVILABLE - 2
AVAILABLE - 3
WRAPUP - 4 

Agent Status Reason

String

Sets the Broadsoft agent status reason code.

Phonebook Groups

String where GroupName;0,OtherGroupName;0

Contains a comma separated list of contact group names.

Ui font Color

Defaults to 0xFFFFFF$0x444343

Sets the default UI color.

Ui Title Color

Defaults to 0x000026$0x4f79a7

Sets the color of UI titles.

Ui Softkey Color

Defaults to up:0x5e6f85$0x485972@ down:0x00$0xffc83b

Sets the color of unpressed and pressed soft keys.

Ui List Color

Defaults to 0x00$0xa9c1c9

Sets the color of UI lists.

Ui Balloon Color

Defaults to 0x00$0x6c7b8d

Sets the color of UI balloons.

Ui Second Color

Defaults to odd:0xc9d9eb$0x9fc0e3@ even:0x356291$0x7296bb@ select:0x34373c$0xe2a917@ interval:0x4478ae@ LSKbgc:0x6b84aa

Sets the color of rows in the UI.

Ui ScrnSaver Color

Defaults to 0x00$0x808080

Sets the color of the screensaver in the UI.

Vqm Display Order

Semi-colon separated list of integers from 1-20

Sets the ordering of the displayed voice quality metrics within the UI as follows:

Start time - 1
Stop time - 2
Local user - 3
Remote user - 4
Local IP - 5
Remote IP - 6
Local port - 7
Remote port - 8
Local codec - 9
Remote codec - 10
Jitter - 11
Jitter Buffer Rate - 12
Jitter Buffer Max - 13
Packets lost - 14
Network Packet Loss rate - 15
MOS-LQ - 16
MOS-CQ - 17
Round Trip Delay - 18
End System Delay - 19
Symm One-Way Delay - 20

DSS Home Page

Integer, Defaults to 0

Sets the home page of any BLF keys. Defaults to 0.

ID

BWCLog[n]

Sets an identifier for the Broadsoft call log where n is from 1-2.

Title

String

Sets the displayed title of the remote Broadsoft call log.

URL

String

Sets the URL of the remote Broadsoft call log.

Username

String

Sets the username used to retrieve the remote Broadsoft call log.

Password

String

Sets the password used to retrieve the remote Broadsoft call log.

SIPLine

Integer, 0-3, Defaults to 0

Sets the SIP line with which to associate the remote Broadsoft call log.

ID

BWDir[n]

Sets an identifier for the Broadsoft directory where n is from 1-6.

Title

String

Sets the displayed title of the remote Broadsoft directory.

URL

String

Sets the URL of the remote Broadsoft directory.

Username

String

Sets the username used to retrieve the remote Broadsoft directory.

Password

String

Sets the password used to retrieve the remote Broadsoft directory.

SIPLine

Integer, 0-3, Defaults to 0

Sets the SIP line with which to associate the remote Broadsoft directory.

ID

LDAP[n]

Sets an identifier for the LDAP phonebook where n is from 1-4.

Title

String

Sets the displayed title of the remote LDAP phonebook.

Server

IPv4 Address or Hostname

Sets the IPv4 address or hostname of the LDAP server.

Port

Integer, 0-4095, Defaults to 389

Sets the port for contacting the LDAP server. Defaults to 389.

Authenticate

Integer, 0-3, Defaults to 3

Specifies the method of authentication to be used against the LDAP server as follows:

None - 0
Digest-MD5 - 1
CRAM-MD5 - 2
Simple - 3

Defaults to 3.

Version

Integer, 2-3, Defaults to 3

Sets the LDAP protocol version to use when communication to the server. Defaults to 3.

Calling Line

Integer, 0-2 or 0-4 (A25), Defaults to 0

If 0, creating calls through the LDAP phonebook will be done via the current line. If the value is 1-4, use the corresponding SIP line to place the calls. Defaults to 0.

Enable Search

Boolean, Defaults to 0

When enabled, query the LDAP server when outbound calls or made, or inbound calls are received. The contacts name will be searched against the LDAP server. The priority is the Local phonebook, followed by the LDAP phonebook, followed by the Display Name of the SIP endpoint. Defaults to 0.

Base

String

Sets the LDAP search root / base for queries.

Username

String

Sets the LDAP server authentication username.

Password

String

Sets the LDAP server authentication password.

Tel Attr

String, defaults to telephoneNumber

Sets the LDAP attribute name to search for telephone numbers.

Mobile Attr

String, defaults to mobile

Sets the LDAP attribute name to search for mobile numbers.

Other Attr

String

Sets an additional LDAP attribute name that can be searched for other numbers.

Displayname

String

Sets the name attribute that should be displayed on the phone.

Filter Name

String

Sets the LDAP search results filter for name filtering. A good example is (|(cn=%)(sn=%))

Filter number

String

Sets the LDAP search results filter for number filtering. A good example is (|(telephoneNumber=%)(mobile=%)(other=%))

ID

XML-PBook[n]

Sets an identifier for the XML phonebook where n is from 1-8.

Name

String

Sets the displayed name of the remote phonebook.

Addr

URL as string

Sets the address of the remote phonebook.

Auth

String

Sets the username and password for retrieving the phonebook.

Policy

Integer, 0, 1, 2, 4, Defaults to 0

Sets the type of authentication used to retrieve the phonebook as follows:

Anonymous - 0
Digest MD5 - 1
CRAM MD5 - 2
Simple - 4

Defaults to 0 

Sipline

Integer, 0-2 or 0-4 (A25)

Sets the SIP line with which to associate the remote phonebook. If set to 0, use the current line. Otherwise, use the specified SIP line, from 1-4.

ID

Fkey[n]

Sets an identifier for the key, where n is an integer 1-11 (A20, A22) or 1-39 (A25)

Type

Integer

Sets the function type of the key as follows:

None - 0
Memory Key - 1
Line - 2
Key Event - 3
DTMF - 4
URL - 7
BLF List - 13
Multicast - 14

Value

String

Value is composed of a complex string assembled as follows:

For Memory Key type keys:
 [number]@[sip account index 1-6]/[subtype][pickup number]
where subtype is as follows:
BLF / New Call - bc
BLF / Blind Transfer - bb
BLF / Attended Transfer - ba
Presence - p
MWI - m
Speed Dial - f
Intercom - i
Call Park - c
Call Forward - a

For Line Key type keys:
SIP[n] where n indicates the SIP line, from 1-6

For Key Event types as follows:

MWI - F_MWI
DND - F_DND
Hold - F_HOLD
Transfer - F_B_TRANSFER
Phonebook - F_PBOOK
Redial - F_REDIAL
Pickup - F_PICKUP
Join - F_JOIN
Call Forward - F_CFWD
Call Logs - F_CALLERS
Flash - F_FLASH
Memo - F_MEMO
Headset - F_HEADSET
Release - F_RELEASE
Lock Phone - F_LOCK
SMS - F_SMS
Call Back - F_LOR
Hide DTMF - F_SDTMF
Prefix - F_PREFIX
Private Hold - F_PRIVATEHOLD
Disposition - F_DISPOSITION
Escalate - F_ESCALATE
Trace - F_TRACE
Group Listen - F_GROUPLISTEN
Local Contacts - F_LOCALCONTACTS
LDAP Group - F_LDAPCONTACTS:[LDAP GROUP ID 1-4]
Cloud/XML Contacts - F_XMLCONTACTS:[XML GROUP 1-4]
Broadsoft Group - F_BWCONTACTS:[Broadsoft Group 1-6]

For DTMF types as the DTMF keys to be transmitted.

For URL types as the URL to be queried. 

For Multicast types as [IP:Port]/Codec where codec is one of: PCMU, PCMA,G726-32,G729,G723,iLBC,AMR, AMR-WB, G722

Where pickup number reflects the extension that will be dialed if the watched party is in the ringing state. Otherwise the number will be dialed

Title

String

Sets the visible, on-screen name of the key.

ID

????

????

Type

????

????

Value

????

????

Title

????

????

Desktop Softkey

Defaults to: history;contact;dnd;menu;

Sets the soft key mapping for the idle screen

Talking Softkey

Defaults to: hold;xfer;conf;end;

Sets the soft key mapping for the on-call screen.

Ringing Softkey

Defaults to: accept;none;cfwd;reject;

Sets the soft key mapping for the ringing (incoming call) screen.

Alerting Softkey

Defaults to: none;none;none;end;

Sets the soft key mapping for the alerting screen.

XAlerting Softkey

Defaults to: xfer;none;none;end;

Sets the soft key mapping for the transfer alerting screen.

Conference Softkey

Defaults to: hold;none;split;end;

Sets the soft key mapping for the conference screen.

Waiting Softkey

Defaults to: hold;xfer;conf;end;

Sets the soft key mapping for the waiting screen.

Ending Softkey

Defaults to: repeat;none;none;end;

Sets the soft key mapping for the ending (far-end has disconnected) screen.

DialerPre Softkey

Defaults to: delete;save;send;exit;

Sets the soft key mapping for the on-hook dialing screen.

DialerCall Softkey

Defaults to: delete;history;send;exit;

Sets the soft key mapping for the on-hook dialing screen, having already entered a digit.

DialerXfer Softkey

Defaults to: delete;xfer;send;exit;

Sets the soft key mapping for the transfer screen.

DialerCfwd Softkey

Defaults to: delete;none;cfwd;exit;

Sets the soft key mapping for the call forwarding screen.

Desktop Click

Defaults to: history;status;paccout;naccout;menu;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the Idle state.

Dailer Click

Defaults to: pline;nline;none;none;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the Dialing state.

Call Click

Defaults to: pcall;ncall;voldown;volup;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) for the on-call state.

Desktop Long Press

Defaults to: status;none;none;sdial;none;

Sets the key mapping for the directional and check keys (up key, down key, left key, right key, check key) when they are long-pressed.

Softkey Mode

Integer, 0-2, Defaults to 1.

If set to 0, custom soft keys are disabled. If set to 1, the More softkey is enabled for keys exceeding four. If set etc 2, the Arrow soft key is used for keys exceeding four. Currently hard-coded to 1.

Softkey Exit Style

Integer, 0-1, Defaults to 1

If set to 0, the exiting soft key will be the left-most key. If set to 1, the exiting soft key will be the right-most key.

Enabled

n/a

Currently unused

Voice Codec

n/a

Currently unused

Enable Server Rec

n/a

Currently unused

Enable PBX Rec

n/a

Currently unused

Server Addr

n/a

Currently unused

Server Port

n/a

Currently unused

Type

n/a

Currently unused

Download Username

String

Sets the optional password that will be passed in when performing retrievals of provisioning files.

Download Password

String

Sets the optional password that will be passed in when performing retrievals of provisioning files.

AP Pswd Encryption

Boolean, Defaults to 0

If enabled, the phone will disguise Auto Update module password. Defaults to 0.

FDPS Enable

Boolean, Defaults to 1

If disabled, does not contact FDPS server on-boot. Defaults to 1.

Config File Name

null, $mac.cfg, $input.cfg

If null, the phone will retrieve a file as <mac>.cfg. If set to $mac, the phone will also retrieve a file as <mac>.cfg. If set to $input.cfg, the phone will prompt the user on the screen to input the file name during boot.

Config File Key

String

Specifies an AES key that must be used to decrypt the device configuration file.

Common Cfg File Key

String

Specifies an AES key that must be used to decrypt the common configuration file. NEED TO GET LIST OF COMMON FILES

Download Server IP

IPv4 Address or Hostname

Specifies the server address for retrieving configuration files.

Download Protocol

Integer, 0, 1, 2, 4, 5, Defaults to 0

Sets the protocol used to contact the provisioning server as follows:

Disabled - 0
FTP - 1
TFTP - 2
HTTP - 4
HTTPs - 5

Defaults to 0

Download Mode

Integer, 0-2, Defaults to 0

Sets the provisioning upgrade type as follows:

Do not download the specified config file - 0
Download the specified config file after reboot - 1
Download the specified config file according to the Download Interval - 2 

Download Interval

Integer, in hours, Defaults to 1

Sets the interval, in hours, at which the phone will download the configuration file if so-specified by Download Mode. Defaults to 1.

DHCP Option

Integer

Sets the method of DHCP option response as follows:

Disable DHCP option downloading - 0
Respond to DHCP option 66 - 66
Respond to DHCP option 43 - 43
Respond to custom option 128-254: 128-254

Defaults to 66 

Save DHCP Opion

Boolean, Defaults to 0

If enabled, the phone will store the DHCP-specified configuration. Defaults to 0.

DHCP Option 120

Boolean, Defaults to 0

If enabled, the phone will retrieve the SIP server address using DHCP Option 120. Defaults to 0.

PNP Enable

Boolean, Defaults to 1

If disabled, the phone will not attempt SIP uPNP for provisioning.