Supported Devices-CyberData

 

 

CyberData Call Button V2

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

  1. Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Ceiling Speaker V2

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Emergency Indoor Intercom V3

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

     

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Indoor Intercom V3

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Indoor Keypad Intercom V2

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Office Ringer V2

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Outdoor Intercom V2 & V3

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Outdoor Keypad Intercom V3

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

  1. Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Adapter V2

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

  1. Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

     

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Gateway V2

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

     

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Server V3

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

     

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Pager Amplifier V2

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the Test/Reset switch while the unit beeps after one second and all indicator lights on the front of the unit come on.

     

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Strobe V2

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Talkback Ceiling Speaker V3

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

     

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

      1. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

CyberData Zone Controller V3

 

How to Find the IP Address

To find this IP Address download CyberData’s VoIP Discovery Utility program, which allows you to easily find and configure the default web address of the CyberData VoIP products. CyberData’s VoIP Discovery Utility program is available at the following website address. http://www.cyberdata.net/support/voip/discovery_utility.html

How to Find the MAC Address

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, you should see the MAC Address under “Current Settings.”

How to Set the Configuration Server

  1. Log in to the Web GUI of the device by putting the IP Address of the device into your browser. Log in to the device when prompted. The factory default username is "admin" and the password is also "admin."

  2. Once logged in, click on the “Autoprovisioning” option on the left side of the screen.

     

  3. Fill in the following information:

    1. Enable Autoprovisioning - Check the box

    2. Get Autoprovisioning from DHCP - Check the box

    3. Autoprovisioning Server (IP Address) - Define the IP Address of your PBX in our example this is 10.10.0.1

 

Don’t forget to press "Save" and then the "Reboot" button at the bottom of the page when done.

How to Restore to Factory Default

  1. Press and hold the RTFM switch until the LED button starts blinking rapidly (about 10 seconds), then release the RTFM switch.

     

  2. Continue to press the switch until after the indicator lights go off, and then release it. The settings for this device are now restored to the factory defaults.

Return to Documentation Home I Return to Sangoma Support